background image

 

ACR8010 Hardware Manual 

P/N PM08121

 

14

ACR8010 MOTHERBOARD JUMPERS 

Encoder Pull-up Select Jumpers (JP19,20,21,23,24,26,27,28,31)  

The ACR8010 is capable of handling various types of incremental open-collector and line 
driver encoders.  Care must be taken to setup each channel to match the encoder type as 
described below:   

The encoder options for the ACR8010 are selectable as follows: 

Encoder 

Options 

Encoders Supplied 

None Not 

Applicable 

1,2,3,4, and 8 

10 

1,2,3,4,5,6,7,8, and 9 

 

Open Collector Encoders: 

When using open-collector encoders, the encoder channels must be pulled to 5 or 
+12 volts, depending upon the application.  Pulling up to +12 volts provides higher noise 
immunity, but causes a slower response time.  For high frequency applications (encoder 
rates higher than 1 megahertz) the +5 volt pull-up section may be necessary.   

Line Driver Encoders: 

When using line driver (or balanced pair) encoders, the corresponding resistor pack 
should be removed from it’s socket.  Leaving the resistor pack in the socket can cause 
faulty encoder operation and possibly severe encoder damage.  Optionally, the resistor 
pack can be replaced with an 8-pin isolated resistor pack to supply termination resistance 
for the balanced signal pairs.   

Pull-up Selection: 

The following table lists the pull-up jumper settings for each encoder: 

 WARNING

 

Wiring a line driver encoder with the pull-up selected to 

+12 volts will permanently damage the encoder.   

 

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for ACR8010

























































Reviews: