Parker BD15 Series, Installation And Service Manual

Flow Control Servovalves

Bulletin HY14-1450-M1/US

Bul 1450-M1pgs.p65, dd

11

Parker Hannifin Corporation

Hydraulic Valve Division
Elyria, Ohio, USA

Ordering Information

Series BD15 and BD30

Code

Description

N

Nitrile (Std.)

V

Fluorocarbon

Connector

Seals

Basic Model

BD

Code Description

A

Standard Valve

B

Intrinsic Safe,
Factory Mutual

C

Explosion Proof,
Factory Mutual

J

Explosion Proof,
CSA Approved

N

Explosion Proof,
ATEX Approved

See Note 1.

Flow

Supply

Pressure

Code

Description

B

2600–3000
(Standard)

C

2000–2500

D

1400–1950

E

1000–1300

F

700–950

G

200–650

H

0–3000
(5th Port)

See Note 3.

Code

15

30

Size

Options

Coil

Mounting Bolt Kit (U.S.)

BD15

BK07 (4) 5/16-18 x 1

BD30

BK46 (4) 5/16-10 x 3 1/4

BD 15

Code

Flow (GPM)

1

3.8 LPM (1 GPM)

2.5

9.5 LPM (2.5 GPM)

5

18.9 LPM (5 GPM)

10

37.9 LPM (10 GPM)

15

56.8 LPM (15 GPM)

20

75.7 LPM (20 GPM)

BD 30

Code

Flow (GPM)

20

75.7 LPM (20 GPM)

25

94.6 LPM (25 GPM)

30

113.6 LPM (30 GPM)

40

151.4 LPM (40 GPM)

BD30

Code

Description

E

C

2

B (Std.)

F

C

2

D

G

C

1

B

H

C

1

D

K

Intrinsic Safe

M

Explosion Proof

See Note 2.

BD15

Code

Description

A

C

2

B (Std.)

B

C

2

D

C

C

1

B

D

C

1

D

J

Intrinsic Safe

L

Explosion Proof

Code

m(A)

Ohm

A

60 (Std.) 60

B

15

1016

C

20

591

D

30

243

E

40

138

F

50

90

G

100

22

H

200

5.7

J*

30/30

118/118

K

80

36

* For intrinsic safe only.

Note 1: “B” Intrinsic Safe Option meets 

Factory Mutual

Intrinsically Safe Class I, II and III, Division 1
Groups A through G. Refer to Parker Bulletin 1452.

“C” Explosion Proof meets:

Factory Mutual Explosion Proof
Class I, II, III, Division 1, Groups A through G

“J” Exposion Proof meets:

Canadian Standards Association
Class I, Groups A through D
Class II, Groups E, F and G
Class III

Refer to Parker Bulletin 1451.

“N” Explosion Proof meets:

ATEX  Ex  II2G EExm II T3 T

amb 

45°C to -50°C

Request Parker Documentation Package: 1200074

Note 2:

Connector Location & Flow Polarity

(Standard connector over C

2

 + to B = P to C

1

 flow).

C

2

B = Connector over Port C

2'

 + to Pin B = P to C

1

 flow.

C

2

D = Connector over Port C

2'

 + to Pin D = P to C

1

 flow.

C

1

B = Connector over Port C

1'

 + to Pin B = P to C

1

 flow.

C

1

D = Connector over Port C

1'

 + to Pin D = P to C

1

 flow.

Note 3:

Supply Pressure: Code “H” applies to 5th Port/External
Pilot Option. This requires the use of a blank orifice “-
00”. First stage pressure should be limited to 41.4 Bar
(600 PSI) and no less than 27.6 Bar (400 PSI).

Servo valve rated flow at 1000 PSID ±10%.