Appendix C
9 9
Motor Size:
A P E X 6 0 2
Value
Units
Tolerance
1
2
3
4
5
Constant (s):
Torque
Voltage (Sinusoidal)
Electrical Time
Mechanical Time
Thermal
52.6 (0.37)
22.5
5.3
1.40
11.0
oz-in/A rms (Nm/A rms)
V rms/Krpm
milliseconds
milliseconds
minutes
±
10%
±
10%
nominal
nominal
nominal
6
7
8
9
10
11
Torque (s):
Continuous, Stall
(NOTE: Values are with
Continuous, Stall
rated and peak current,
Continuous, Rated
lines 15 & 16 below.
Peak, Max w/o Saturation
Drive current, and thus
Static Friction
torque, may be lower.)
Ripple (of Rated Torque)
236 (1.67)
223 (1.57)
202 (1.43)
630 (4.45)
7.68 (0.05)
5
oz-in (Nm)
oz-in (Nm)
oz-in (Nm)
oz-in (Nm)
oz-in (Nm)
percent
min. [1]
min. [2]
min. [2]
min. [1]
max.
max. [3]
12
13
Speed:
Rated
Maximum
7500 (125)
7500 (125)
rpm (rps)
rpm (rps)
reference
reference
14
Frequency
Rated
250
Hz
max.
15
16
Current:
Rated
Peak
4.2
12.6
A rms
A rms
max. [1]
nominal
17
18
Voltage:
Rated
Max
240
250
V rms
V rms
reference
maximum
19
Output Power
Rated
1.12 (1.5)
kWatts (hp)
min. [1]
20
Inductance
Terminal (line-line)
14.4
mH
±
30%
21
D.C. Resistance
Terminal (line-line)
2.72
ohms
±
10 % [1]
22
Acceleration at Rated Torque
96500
rads/sec
2
Theoretical
23
Rotor Inertia
2.52 (46.1)
oz-in
2
(kgm
2
∗
1E-6)
nominal
24
Damping
0.384 (0.0027)
oz-in/krpm (Nm/krpm)
nominal
25
Weight
7.0 (3.17)
lbs. (kg)
max.
26
Winding Temperature
170
°
C (338
°
F) [4]
°
C (
°
F)
max.
27
Winding Temperature Rise (Above Ambient) [1]
145
°
C (293
°
F)
°
C (
°
F)
reference
28
Insulation Class
H
—
reference
29
Thermostat TRIP Temperature
170
°
C (338
°
F)
°
C (
°
F)
±
5
°
C
30
Thermostat RESET Temperature
135
°
C (275
°
F)
°
C (
°
F)
±
10
°
C
31
Dielectric Strength, (Winding-to-Frame)
1750
VAC
min.
32
Winding Capacitance-to-Frame
0.000898
µ
F
max.
33
IP Classification
65 [8]
rated
standard
34
Shaft:
Radial-Play At
End
At Faceplate
12E-6 (68E-9)
7.0E-6 (40E-9)
in/lb (m/N)
in/lb (m/N)
reference
reference
35
Material [5]
RC-#30
—
reference
36
Magnet Type
NdFeB
—
—
37
Loading [6]
1000 rpm (17 rps)
2000 rpm (33 rps)
3000 rpm (50 rps)
4000 rpm (67 rps)
5000 rpm (83 rps)
81 (360)
65 (289)
56 (249)
51 (227)
48 (213)
lbs. (N)
lbs. (N)
lbs. (N)
lbs. (N)
lbs. (N)
max. [7]
max. [7]
max. [7]
max. [7]
max. [7]
38
Motor Vibration
N
ISO 2373
Standard
39
Bearing Class, Internal/External
1/Class 3
ABEC/AFBMA
reference
40
Bearing Grease
SRI #2
Manufacturer
reference
41
Shaft Seal Pressure
3 (0.21)
psi (kg/cm
2)
max.
42
Basic Motor Design
3 phase
wye connected 2(P/2)
43
Stator Phase Sequence
A-C-B (viewed from front face plate)
44
Vendor/Supplier
Industrial Drives B-104-B
45
Resolver Type/Accuracy
Single-Speed; Rotor-Excited;
±
10 arc min.;
Resolution is 4096 counts/rev post-quadrature
46
Resolver Manufacturer/Model #
Fasco # 21-BRCX-335-J39
47
Standard Resolver Cable Part Number
71-011777-xx
48
Standard Motor Cable Part Number
71-011774-xx
49
Options:
Brake—24VDC (0.57A)—326 oz-in (2.3 Nm) Holding Torque
(requires resolver
IP67 Classification
No Keyway
cable 71-014082-xx)
Incremental Encoder
Shaft Modifications
Tachometer
IP65 Shaft Seal
[1] 25
°
C (77
°
F) Ambient
[2] 40
°
C (104
°
F) Ambient
[3] Measured at 60 rpm (1 rps) in Velocity Mode
[4] Rated for 20,000 Hours or 40,000 Hours
@ 155
°
C (311
°
F)
[5] Rotor steel is rated as
fatigue proof
[6] Loads centered 1 inch from mounting flange
[7] Loads may be radial and axial such that the sum of the
radial and two times the axial does not exceed this figure.
[8] Motor shaft is IP30 rated.
APEX602 Motor Specifications
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
