background image

Warranty

This warranty applies to the generator and associated parts (the equipment) manufactured and supplied by Parker Hannifin 
Manufacturing Limited., domnick hunter Filtration and Separation (the company).

Use of the generator without the recommended inlet air quality or genuine parts will expressly invalidate the warranty.

Should the equipment be defective as to materials or workmanship, the company warrants that it will remedy such defect. Where 
the equipment is the generator, the warranty period will be 12 months from date of commissioning or 18 months from date of 
manufacture, whichever comes first. In the case of equipment other than the generator, the warranty period shall commence 
from the date of dispatch.

Should any defect occur during the warranty period and be notified in writing to the company or its authorised distributor within 
the said period, the company will, as its sole option, remedy such defect by repair or provision of a replacement part, provided 
that the equipment has been used strictly in accordance with the instructions provided with each item of equipment and has been 
stored, installed, commissioned, operated and maintained in accordance with such instruction and with good practice. The 
company shall not be under any liability whatsoever under the warranty, if, before giving notification in writing to the company as 
aforesaid, the Customer or any third party meddles, interferes, tampers with or carries out work whatsoever (apart from normal 
maintenance as specified in the said instructions) in relation to the equipment or any part thereof.

Any accessories, parts and equipment supplied by the company but not manufactured by the company shall carry whatever 
warranty the manufacturer has given the company providing it is possible for the company to pass on such warranty to the 
customer.

To claim under the warranty, the goods must have been installed and continually maintained in the manner specified in the User 
Guide. Our product support engineers are qualified and equipped to assist you in this respect. They are also available to make 
repairs that may become necessary in which event they will require an official order before carrying out the work. If such work is 
to be the subject of a warranty claim, the order should be endorsed for consideration under warranty.

Where equipment is sold outside the UK mainland direct to the end user the warranty will cover parts only. Any substitution of 
parts not manufactured or approved by the company will expressly invalidate the warranty.

Summary of Contents for domnick hunter UHP10ZA-S





















Reviews: