Filter
w/Manual Drain
Introduction
Follow these instructions when installing, operating, or servicing
the product.
Application Limits
These products are intended for use in general purpose
compressed air systems only.
CAUTION
Polyurethane bowls, sight glass and sight domes on these
units may be attacked by certain chemicals. Never use
solvents like carbon tetrachloride, trichlorethylene, acetone,
or paint thinner to clean any parts. These elements can
cause crazing or failure of the plastic parts. The
polyurethane resin parts are compatible with most
hydrocarbon based synthetic lubricants but, before using,
check with the manufacturer of the lubricant or oil for
compatibility with polyurethane resin.
TO CLEAN POLYURETHANE BOWLS USE MILD SOAP
AND WATER ONLY!
WARNING
To avoid unpredictable system behavior that can cause personal injury
and property damage:
•
Disconnect electrical supply (when necessary) before installation,
servicing, or conversion.
•
Disconnect air supply and depressurize all air lines connected to
this product before installation, servicing, or conversion.
•
Operate within the manufacturer’s specified pressure, temperature,
and other conditions listed in these instructions.
•
Medium must be moisture-free if ambient temperature is below
freezing.
•
Service according to procedures listed in these instructions.
•
Installation, service, and conversion of these products must be
performed by knowledgeable personnel who understand how
pneumatic products are to be applied.
•
After installation, servicing, or conversion, air and electrical
supplies (when necessary) should be connected and the product
tested for proper function and leakage. If audible leakage is present,
or the product does not operate properly, do not put into use.
•
Warnings and specifications on the product should not be covered
by paint, etc. If masking is not possible, contact your local
representative for replacement labels.
WARNING
FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF
THE PRODUCTS AND/OR SYSTEMS DESCRIBED HEREIN OR
RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND
PROPERTY DAMAGE.
This document and other information from The Company, its
subsidiaries and authorized distributors provide product and/or system
options for further investigation by users having technical expertise. It
is important that you analyze all aspects of your application, including
consequences of any failure and review the information concerning
the product or systems in the current product catalog. Due to the
variety of operating conditions and applications for these products or
systems, the user, through its own analysis and testing, is solely
responsible for making the final selection of the products and systems
and assuring that all performance, safety and warning requirements
of the application are met.
The products described herein, including without limitation, product
features, specifications, designs, availability and pricing, are subject
to change by The Company and its subsidiaries at any time without
notice.
EXTRA COPIES OF THESE INSTRUCTIONS ARE AVAILABLE FOR
INCLUSION IN EQUIPMENT / MAINTENANCE MANUALS THAT UTILIZE
THESE PRODUCTS. CONTACT YOUR LOCAL REPRESENTATIVE.
Maximum Recommended Pressure Drop:
kPa
PSIG
bar
Particulate Filter
70
10
0.7
With Polyurethane Bowl
kPa
PSIG
bar
Operating Pressure Maximum
1034
150
10.0
Operating Temperature Range
4.4°C to 48.9°C
(40°F to 120°F)
With Zinc Bowl
kPa
PSIG
bar
Operating Pressure Maximum
2068
300
21.0
Operating Temperature Range
4.4°C to 82.0°C
(40°F to 180°F)
With Zinc Bowl & Wrap Around Sight Gauge
kPa
PSIG
bar
Operating Pressure Maximum
1723
250
17.0
Operating Temperature Range
4.4°C to 65.60°C
(40°F to 150°F)
Piston Drain Installed
kPa
PSIG
bar
Operating Pressure Maximum
1207
175
12.0
Operating Temperature Range
4.4°C to 65.60°C
(40°F to 150°F)
ANSI Symbols
!
!
!
Pneumatic Division
Richland, Michigan 49083
269-629-5000
Installation & Service Instructions
IS-F35
F35 Particulate Filter
ISSUED: February, 2005
Doc. #ISF35, ECN #050142, Rev. 1
