background image

11

Parker Hannifin Corporation

Helac/Cylinder Division

Enumclaw, Washington USA

www.helac.com

PowerTilt Tilting Coupler

PT-4.5 Service & Repair Manual

HY34-1370  

PowerTilt Warranty

Helac Corporation warrants its products to be free from defects in material and factory workmanship for a 

period of two (2) years or 2,000 service hours, whichever occurs first, for applications defined as medium 

duty, on the machine for which the Helac Attachment (PowerTilt® or PowerGrip®) was originally designed 
and with cross port or work port relief valves installed according to Helac Corporation’s recommendations. 

The warranty period shall begin when the Helac Attachment is first placed into service as documented on 

the Warranty Registration Card. Parts and labor will be covered for the first 12 months or 1000 service 

hours after the start of the warranty period. Parts only will be covered for the remainder of the warranty 
period. 

This warranty shall be voided as to any products which have been repaired, worked upon, or altered by 
persons not authorized by Helac Corporation, or which have been subject to misuse, misapplication, 

negligence, accident, overload, field alteration, severe use or service applications beyond what the Helac 

Attachment was designed to perform. In no event shall Helac Corporation be liable for any incidental 
or consequential damages or claims including, but not limited to, the application in which the product 

was placed, field travel, freight charges, oil samples, downtime, etc. Warranty related repair and/or 

replacement issues will be satisfied according to how the product was originally purchased.

Helac Corporation reserves the right to make changes in the design or construction of any of its products 
at any time without incurring any obligations to make changes or alterations to products previously sold. 
Helac Corporation reserves the right to alter this warranty and/or its terms at any time. This warranty 
is in lieu of all other and/or prior warranties, expressed or implied, and no other company or person is 
authorized to represent or assume for Helac Corporation any liability in connection with the sale of Helac 
Corporation products other than set forth herein.

Warranty Information

Summary of Contents for Helac PowerTilt PT-4.5













Reviews: