Parker Helac PowerTilt PT-4.5 Service And Repair Manual Download | Manualshive

Page: 9 / 12

background image

9

Parker Hannifin Corporation

Helac/Cylinder Division

Enumclaw, Washington USA

www.helac.com

PowerTilt Tilting Coupler

PT-4.5 Service & Repair Manual

HY34-1370

Install Quick Coupler

1.

Install coupler on PowerTilt. Insert 8 ea. M10

screws (114) with washers (115) through lock
plate (412) and torque to 68 Nm (50 ft-lbs).

.

2.

Insert screw (409), 1” tie-rod bolt through

center of PowerTilt from the torque foot end,
install spacer (410) and lock-nut (411) and
torque to 920 Nm (680 ft-lbs).

.

Install Quick Coupler

«
...
7
8
9
10
11
...
»

Summary of Contents for Helac PowerTilt PT-4.5













Reviews:

No comments

Related manuals for Helac PowerTilt PT-4.5

Brand: KAKA Industrial Pages: 10

Brand: Rapid Pages: 93

Brand: Rapid Pages: 140

Brand: TE Connectivity Pages: 8

Brand: Wacker Neuson Pages: 52

Brand: Black+Decker Pages: 32

Brand: SIXTOL Pages: 24

Brand: Rehau Pages: 36

Brand: molex Pages: 6

Brand: Parkside Pages: 65

Brand: Graco Pages: 54

Brand: Gage Bilt Pages: 24

Brand: Matco Tools Pages: 4

Brand: Compac Pages: 24

Brand: MK Pages: 56

Brand: Cutech Pages: 33

CAT-HT-182-2430-11

Brand: Samtec Pages: 4

50/65 Ton Ironworker G0647

Brand: Grizzly Pages: 76

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands