background image

 

viii 

 

Safety 

 

 

Welding after installation 

Complete as much as possible of the welding work on the chassis before the 
installation of the system. If welding must be done afterwards, proceed as 
follows: 

 Do not place the welding unit cables near the electrical wires of the 

control system. 

1.

 

Disconnect the electrical connections between the system and external 
equipment. 

2.

 

Disconnect the negative cable from the battery.  

3.

 

Disconnect the positive cable from the battery. 

4.

 

Connect the welder's ground wire as close as possible to the place of the 
welding. 

 

Construction regulations 

The vehicle must be equipped with an emergency stop which disconnects the 
supply voltage to the control system's electrical units. The emergency stop must 
be easily accessible to the operator. If possible, the machine must be built so that 
the supply voltage to the control system's electrical units is disconnected when 
the operator leav

es the operator’s station.

 

 

Safety during installation 

 Incorrectly positioned or mounted cabling can be influenced by radio 

signals, which can interfere with the functions of the system. 

 

 

Safety during start-up 

 

Danger! Risk of death or injury.

 Do not start the machine's engine 

before the control system is mounted and its electrical functions have 
been verified. Do not start the machine if anyone is near the machine. 

 

 

Summary of Contents for PVSG-IQAN-C2E1M2W1U1







































































Reviews: