Visit:
www.parker.com/conditionmonitoring
Call:
(763) 544-7781
Email:
qcdiot@parker.com
For more information on
SensoNODE
and
Voice of the Machine
products:
Have
questions
or need
help?
Setup an Analog Connector
The Analog Connector will display in Voice of the Machine Cloud as Offline. This is because
the transmitter does not have a sensor connected. Once a sensor is connected, the data will
display within Voice of the Machine Cloud.
1. Login to Voice of the Machine Cloud
2. Click on
DEVICES
tab
3. Click delete
X
next to Analog Connector
4. Click
OK
on pop-up
5. Click
+ New Device
6. Input a
Device Name
7. Select
Analog Connector
from
Device Type
drop-down
8. Input
Serial Number
from rear sticker of Analog connector,
begins with ED (see Figure 3)
9. Select desired Data Type from
Mapping
drop-down
10. Input mapped numerical value for
4mA
11. Input mapped numerical value for
20mA
12. Click
SUBMIT
Parker Hannifin Corporation
Quick Coupling Division
8145 Lewis Road
Minneapolis, MN 55427
phone 763 544 7781
fax 763 544 3418
Starter Kit Instructions 12/18
© 2018 Parker Hannifin Corporation
Unites States
This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by on or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Canada
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference
that may cause undesired operation of the device
Cet appareil est conforme aux normes RSS exemptes de licence d’Industrie Canada.
Son fonctionnement est soumis aux conditions suivantes: (1) cet appareil ne doit pas
causer d’interférences, et (2) cet appareil doit accepter toute interférence, y compris
les interférences pouvant provoquer un fonctionnement indésirable de l’appareil.
Notice:
This radio transmitter (IC: 8975A-A10040601) has been approved by Industry
Canada to operate with the antenna types listed below with the maximum permissible
gain and required antenna impedance for each antenna type indicated. Antenna types
not included in this list, having a gain greater than the maximum gain indicated for that
type, are strictly prohibited for use with this device.
Avis: Cet émetteur radio (IC: 8975A-A10040601) a été approuvé par Industrie Canada
pour fonctionner avec les types d’antennes énumérés ci-dessous avec le gain
maximal admissible et l’impédance d’antenne requise pour chaque type d’antenne
indiqué. Les types d’antennes ne figurant pas dans cette liste, ayant un gain supérieur
au gain maximal indiqué pour ce type, sont strictement interdits pour l’utilisation avec
cet appareil.
Antenna:
Parker P/N: QX-008-387 (Gain: 0±1.5 dBi;
Impedence – Nominal: 50 ohms)
EU Digital Transmission System
868MHz Radio Module:
Frequency Range: 868-870MHz
Output Power: 13.63 dBm ERP
Sign into our Condition Monitoring Service Desk
at
https://phscout.atlassian.net/servicedesk/customer/portals
INST 3864-SK
