background image

CALL TOLL-FREE:
1-888-926-5517

Ext. 1 - Sales & Service
Ext. 2 - Administration

OFFICE HOURS (WEEKDAYS)
8AM-4PM EST

sales@parkit360.com
admin@parkit360.com
support@parkit360.com

DISCONNECTING THE HITCH

Chock Trailer Wheels

 to prevent a runaway trailer.  

Unplug the Battery Cable

 from the Dolly. 

Raise the Trailer

 to 

withdraw the 

Ball Mount

, then switch to 

Freewheel Mode

.

The Ball Mount can be removed or left on the hitch for later use.

STORAGE & MAINTENANCE

Freewheel the Dolly to desired storage area, preferably under cover.

Charging the On-Board Battery: 

Plug the Battery Cable into the Dolly. 

Unplug the Handle Cable, then plug the Dolly’s Charger Cable into a 
wall outlet. Stops charging automatically when full.

Grease the Receiver Tube 

and 

Lubricate the Chain 

with

 Chain Lube. 

Can be done annually, or more often if used more frequently.

PARKING YOUR TRAILER

Use the 

Forward 

and

 Reverse

 Toggle Switch to steer  

into tight spaces that are nearly impossible for vehicles.

Switch between 

High 

or 

Low Speed

 anytime using the  

Intelligent Speed Control

 Switch.

Summary of Contents for FORCE 10K

















Reviews: