background image

10  GB/IE

  Impact force controller 

2

Increase impact force:

   

Turn the impact force controller 

2

 anticlockwise.

Decrease impact force:

   

Turn the impact force controller 

2

 clockwise.

Q   

Use

Q   

Switching on and off

   

Set the ON / OFF switch 

3

 to position “I” to 

switch on the device.

   

Set the ON / OFF switch 

3

 to position “0” to 

switch off the device.

Q   

Stapling / nailing

   

Switch the device on by setting the ON / OFF 
switch 

3

 to position “I”.

   

Press the device with its front plate 

7

 at the 

point on the surface of the material where you 
wish to staple or nail. 

   

Press the trigger 

1

NOTE:

 The integral safety lock in the front 

plate prevents unintentional firing.

Q   

Troubleshooting

Cause:

A staple or nail is blocking the device. 

Solution:

   

Open the magazine slider 

4

. This releases 

the pretension. Release the screws on the front 
plate 

7

 using the hex key (Fig. D). 

   

Remove the staple or nail.

Q   

Maintenance and cleaning

 DANGER OF INJURY!

 Pull 

the mains plug out of the mains socket before you 
clean or maintain the device.

The electric nailer / stapler is designed to be main-
tenance-free.

   

Always keep the device clean, dry and free 
from oil or grease.

   

Clean the device immediately after you have 
finished using it. 

   

Do not allow any liquids to enter the device. 

   

Use a cloth to clean the housing. Never use 
petrol, solvents or cleaning agents that might 
attack plastic.

Q   

Service

   

 

Have your device  

repaired at the service centre or by 
qualified specialist personnel using  
original manufacturer parts only.

 This 

will ensure that your device remains safe to use.

   

 

If the plug or lead 

needs to be replaced, always have 
the replacement carried out by the 
manufacturer or its service centre. 

This 

will ensure that your device remains safe to use.

Note: 

Spare parts not listed (e.g. carbon brushes, 

switches) can be ordered through our call centre.

Q   

Warranty

The warranty for this appliance is for 3 
years from the date of purchase. The ap-
pliance has been manufactured with care 
and meticulously examined before deliv-
ery. Please retain your receipt as proof 
of purchase. In the event of a warranty 
claim, please make contact by telephone 
with our Service Department. Only in this 
way can a post-free despatch for your 
goods be assured.

The warranty covers only claims for material and 
maufacturing defects, but not for transport damage, 
for wearing parts or for damage to fragile compo-
nents, e.g. buttons or batteries. This product is for pri-
vate use only and is not intended for commercial use.

… / Disposal /Translation of the original declaration of conformity / Manufacturer

Before  use / Use / Maintenance  and  cleaning / Service / Warranty

Summary of Contents for 273474






























Reviews: