PFBS 160 B2
GB
│
IE
│
NI
│
CY
│
5
■
4. Power tool use and care
a)
Do not force the power tool. Use the correct
power tool for your application.
The correct
power tool will do the job better and safer at
the rate for which it was designed.
b)
Do not use the power tool if the switch does
not turn it on and off.
Any power tool that can-
not be controlled with the switch is dangerous
and must be repaired.
c)
Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools.
Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
d)
Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool.
Power tools are
dangerous in the hands of untrained users.
e)
Maintain power tools. Check for misalign-
ment or binding of moving parts, breakage of
parts and any other condition that may affect
the power tool's operation. If damaged, have
the power tool repaired before use.
Many ac-
cidents are caused by poorly maintained power
tools.
f)
Keep cutting tools sharp and clean.
Properly
maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
g)
Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed.
Use of the
power tool for operations different from those
intended could result in a hazardous situation.
5. Service
a)
Have your power tool serviced by a qualified
repair person using only identical replace-
ment parts.
This will ensure that the safety of
the power tool is maintained.
WARNING!
Always wear safety googles
Safety instructions for all applica-
tions
General safety instructions for grinding, sand-
paper sanding, working with wire brushes,
polishing, milling and abrasive cutting:
a)
This power tool is intended for use as a grinder,
sandpaper sander, wire brush, polisher,
milling machine and abrasive cutting appli-
ance. Please follow all safety instructions,
directives, diagrams and data that you re-
ceive with the appliance.
If you do not observe
the following instructions, this can lead to an
electrical shock, fire and/or serious injuries.
b)
Do not use any accessories that have not
been provided or recommended for this
power tool by the manufacturer.
Just because
you can attach the accessories to your power
tool, does not guarantee they are safe to use.
c)
The permissible speed of the attachment part
must be at least as high as the maximum speed
specified for the power tool.
Accessories that
rotate faster than the permissible rate can break
and throw pieces into the air.
d)
The external diameter and thickness of the
attachment part used must comply with the
dimensions of the power tool.
Incorrectly
dimensioned accessory tools cannot be suf-
ficiently shielded or controlled.
Summary of Contents for 286851
