Parkside 286851, Translation Of The Original Instructions

PFBS 160 B2

■ 

6 

│

GB

│

IE

│

NI

│

CY

e)  

Grinding discs, sanding drums or other ac-
cessories must match exactly the grinding 
spindle or collet chuck of your power tool. 

Ac-

cessory tools which do not fit precisely into the 
take-up of the power tool will rotate unevenly, vi-
brate severely and can lead to a loss of control.

f)  

Discs, grinding cylinders, cutting tools or 
other accessories mounted on a mandrel must 
be inserted completely in the collet or chuck. 
Any "protrusion" or exposed parts of the 
mandrel between the grinding tool and the 
collet or chuck must be kept to a minimum. 

If 

the mandrel is not sufficiently tightened or the 
grinding tool protrudes too far, the attachment 
part can come loose and be ejected at high 
speed.

g)  

Never use damaged attachment parts.  
Before each use, check accessory tools such 
as grinding discs for chips or cracks, sanding 
drums for cracks, wearing or excessive wear 
and tear and wire brushes for loose or broken 
wires. If the power tool or the attachment part 
is dropped, check to see if it is damaged or 
use an undamaged attachment part. When 
you have checked and inserted the attachment 
part, ensure that you and any other people 
nearby remain outside of the range of the 
rotating attachment part and allow the tool 
to rotate at maximum speed for one minute. 

Damaged accessory tools usually break during 
this test period.

h)  

Wear personal protective equipment.  
Depending on the application, ensure that 
you use full face protection, eye protection or 
goggles. If appropriate, use a dust mask, ear 
protectors, protective gloves or special apron 
to protect you from grindings and material 
particles. 

The eyes should be protected from 

flying debris that may be caused during certain 
applications. Dust or filter masks must be used 
to filter any dust created by the application. If 
you are exposed to loud noise for any length  
of time, you can suffer a hearing loss.

i)  

Ensure that other people remain at a safe dis-
tance to your workspace. Anyone who enters 
the workspace must wear personal protective 
equipment. 

Fragments of the workpiece or bro-

ken accessory tools can fly off and cause injury 
– even outside the immediate working area.

j)  

Hold the power tool only by the insulated 
gripping surfaces when performing work 
during which the attachment part can contact 
hidden wiring or its own cord. 

Contact with 

a live cable may also cause metal parts of the 
appliance to become live and may result in an 
electric shock.

k)  

Always hold the power tool firmly. 

When 

running up to full speed, the torque of the motor 
can cause the power tool to twist.

l)  

If possible, use clamps to hold the workpiece 
in position. Never hold a small workpiece 
in one hand and the power tool in the other 
while you are using it. 

By clamping small 

workpieces, you keep both hands free for better 
control of the power tool. When cutting round 
workpieces such as dowels, rods or pipes, be 
aware that these can roll away and this can 
cause the tool to jam and be thrown towards 
you.

m)  

Hold the power cord away from any rotating 
accessories. 

If you lose control of the appli-

ance, the cord may get cut or caught and your 
hand or arm could get caught in the rotating 
accessory tool.

n)  

Never put the power tool down until the 
attachment part has come to a complete 
standstill. 

The rotating accessory tool could 

come into contact with the surface and cause 
you to lose control of the power tool.

o)  

When changing attachment parts or the 
settings on the appliance, tighten the collet 
nut, the chuck or other fixing elements tightly. 

Loose fastening elements can shift unexpectedly 
and lead to loss of control; unsecured, rotating 
components will fly off violently.

p)  

Do not leave the power tool running while 
you carry it. 

Accidental contact between your 

clothing and the rotating accessory tool could 
lead to a physical injury.