8 GB/CY
Wear a dust mask!
Wear protective glasses!
Wear ear protection!
Wear protective gloves!
Wear protective clothing!
EXPLOSION HAZARD!
Do not
use the air sand blaster gun in envi-
ronments containing gases, open
flames, fires or gas-operated water heaters.
SMOKING PROHIBITED!
Only work in well ventilated spaces.
Never use oxygen or other flammable gases
as an energy source.
Never exceed the maximum permitted operat-
ing pressure of 6.3 bar.
RISK OF RECOIL
FORCES!
High operating pressures can give rise
to recoil forces that under certain conditions
can result in danger from continuous loading.
RISK OF INJURY!
Remove the product from
the compressed air source before repair and
maintenance work and before transport.
RISK OF INJURY!
Remove the product from
the compressed air source to fill the product
with blasting material.
NOTE!
Please note the safety information of the
manufacturer of the blasting material.
Only use suitable materials for the air sand
blaster gun. Use a suitable blasting material!
ATTENTION!
Heavy dust forma-
tion. Take precautions!
Make sure that the sandblasting material is
collected so that you can dispose of it in an
environmentally-friendly way.
Do not remove any markings/type plates.
These are safety-relevant.
If you are inexperienced in the use of this type
of product, you should seek training to learn
how to handle it safely.
WARNING! NOXIOUS DUST!
Working
on materials which can produce harmful / toxic
dusts presents a health risk to the user and peo-
ple within close vicinity.
CAUTION
Ensure that the product
is disconnected from the air supply
when it is not in use, when replacing
accessories or when carrying out repair work.
The air hose must not be pressurised.
Operation
Connecting the compressed air
source
Note:
The air sand blaster gun
3
may only be
operated using purified, oil-free and condensate-
free compressed air with a maximum pressure of
6.3 bar. To regulate the compressed air you should
use a pressure regulator and filter.
Note:
Ensure that the rotary control
9
is at „0“
before connecting the product to the compressed
air source.
Connect the air sand blaster gun
3
to a suitable
compressed air source. Now connect the supply
pipe using the quick coupling to the coupling
plug
4
on the air sand blaster gun
3
. This
automatically locks into place.
Filling the blasting material
holder
CAUTION
Before opening the
screw cap
2
of the blasting material
holder
1
or configuring other set-
tings, the pressure must always be fully relieved
and the air sand blaster gun disconnected from
the compressed air source (i.e. compressor).
Only use a suitable blasting material for your
work
14
.
Note:
We recommend sandblasting material
(ground blast furnace slag) which does not
Summary of Contents for 298505
