Parkside 313266 1904, Translation Of The Original Instructions

■ 

36 

│

GB

│

MT

PHSHE 900 B2

Before use

CAUTION! RISK OF INJURY!

►

Before any work on the appliance, disconnect the plug.  
Risk of electric shock!

Motor unit

Attaching the round handle

♦

Place the round handle   in the desired position on the boom  .

♦

Tighten the screw  .

Assembling the quick release mechanism

♦

Hook in the carabiner and secure it with the red strap on the quick 
release mechanism (see figures). Pull on the red strap if you have to 
put down the appliance quickly.

Fastening/attaching the shoulder strap

♦

Hook the shoulder strap   into the carrying lug  .

♦

Adjust the length of the shoulder strap   to your size so that the carrying 
lug   is at hip height when the strap is hooked in place.

Assembling the hedge trimmer

♦

Push the front boom   of the hedge trimmer onto the boom   of the 
motor unit.

♦

The locking pin   must engage.

♦

Secure the two booms     with the tommy screw  ; to do this, fit 
the nut   on the opposite side.

Mounting the pole pruner

♦

Push the front boom   of the pole pruner to the boom   of the motor 
unit.

♦

The locking pin   must click into place.

♦

Secure the two booms     with the tommy screw  ; to do this, fit 
the nut   on the opposite side.

Swivelling of the hedge trimmer

♦

Trigger the lock/release  .

♦

Press the control lever   and swivel the hedge trimmer into the 
desired position.

♦

Allow the control lever   and the lock/release   to click into the 
recess in the base plate (hedge trimmer)  .

Swivelling of the pole pruner

♦

Release the lock/release  .

♦

Press the control lever   and swivel the pole pruner into the desired 
position.

♦

Allow the control lever   and the lock/release   to click into the 
recess in the base plate (pole pruner)  .

Mounting the saw chain and blade

WARNING!

►

Wear protective gloves! There is a danger of injury from the sharp 
cutting teeth!

NOTE

►

Pay close attention to the running direction of the saw chain   on 
the blade   and at the sprocket cover  .

►

The blade   and the saw chain   are already assembled upon 
delivery.

►

Depending on wear, the blade   can be turned.

♦

Undo the nut   using the assembly tool  .

♦

Remove the sprocket cover  .

♦

You may have to loosen the saw chain   to remove the blade   
and the saw chain   (see section "Tightening and checking the saw 
chain"). Follow these instructions in reverse order.

♦

Remove the blade   with the saw chain   from the base plate  
(pole pruner)  .

♦

Reset the saw chain   starting at the top of the blade  .

♦

Lay the guide rail   over the blade guide  , while inserting the chain 
roll pin   in the blade hole  . At the same time, lay the saw chain   
over the chain sprocket  .

♦

Now you can tighten the saw chain   (see section “Tightening and 
checking the saw chain”).

♦

Replace the sprocket cover   and tighten the nut   gently.

Tightening and checking the saw chain

NOTE

►

The tension of the saw chain   is important for your safety and the 
function of the appliance. A correctly pre-stressed saw chain   
increases the service life of your appliance.

WARNING!

►

Wear protective gloves! There is a danger of injury from the sharp 
cutting teeth!

♦

Loosen the nut   a little using the assembly tool  .

♦

Using the assembly tool  , turn the chain adjuster screw   in a  
clockwise direction to increase the tension.

♦

Using the assembly tool  , turn the chain adjuster screw   in an 
anticlockwise direction to decrease the tension.

♦

The saw chain   must lie against the underside of the blade. Check 
whether the saw chain   can be drawn over the blade   by hand.

♦

Tighten the nut   using the assembly tool  .

NOTE

►

When pulling on the saw chain   with a force of 9 N (approx. 1 kg), 
the gap between the saw chain   and blade   should not be more 
than 2 mm.

►

A new saw chain   stretches and must be tightened more frequently.

►

Check the chain tension before each use of the appliance.