Parkside 327366 1904 Operating And Safety Instructions, Translation Of Original Operating Manual Download

Page: 17 / 80

GB/IE

2. Introduction

Manufacturer:

scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen

Dear Customer,

We hope your new tool brings you much enjoyment and suc-
cess.

Note:

According to the applicable product liability laws, the manu-
facturer of the device does not assume liability for damages
to the product or damages caused by the product that occurs
due to:
• Improper handling,
• Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service techni-

cians,

• Installation and replacement of non-original spare parts,
• Application other than specified,
• A breakdown of the electrical system that occurs due to the

non-compliance of the electric regulations and local regula-
tions.

We recommend:

Read through the complete text in the operating instructions be-
fore installing and commissioning the device.
The operating instructions are intended to help the user to be-
come familiar with the machine and take advantage of its ap-
plication possibilities in accordance with the recommendations.
The operating instructions contain important information on
how to operate the machine safely, professionally and econom-
ically, how to avoid danger, costly repairs, reduce downtimes
and how to increase reliability and service life of the machine.
In addition to the safety regulations in the operating instruc-
tions, you have to meet the applicable regulations that apply
for the operation of the machine in your country.
Keep the operating instructions package with the machine at
all times and store it in a plastic cover to protect it from dirt
and moisture. Read the instruction manual each time before
operating the machine and carefully follow its information. The
machine can only be operated by persons who were instructed
concerning the operation of the machine and who are informed
about the associated dangers. The minimum age requirement
must be complied with.
In addition to the safety instructions contained in this operating
manual and the specific regulations of your country, the techni-
cal rules generally accepted for the operation of machines of
the same type must be observed.
We accept no liability for damage or accidents which arise
due to non-observance of these instructions and the safety in-
formation.

3. Device description (Fig. 1-14)

1.  Transport handle
2.  Pressure switch
3.  Quick-lock coupling (regulated compressed air)
4.  Pressure gauge (for reading the preset vessel pressure)
5.  Pressure regulator
6.  Pressure gauge (for reading the vessel pressure)
7.  Quick-lock coupling (unregulated compressed air)
8.  Pressure vessel
9.  Supporting foot
10.  Drain plug for condensation water
11.  Wheel
12.  Oil drain plug
13.  Compressor pump
14.  Compressed air hose
15.  Air filter
16.  Oil sealing plug
17.  ON/OFF switch
18.  Oil – level window
19.  Safety valve
20.  Oil filler opening
21.  Flange screw
22.  Washer
23.  Screw
24.  Overload switch
25.  Screw (pre-mounted)

4. Scope of delivery

1x Air filter
2x Supporting foot
2x Wheel
1x Transport handle
1x Mounting material
1x Oil sealing plug
1x Oil bottle
1x Compressed air hose
1x Translation of Original Operating Manual

5. Intended use

The compressor is designed to generate compressed air for
compressed-air driven tools which can be driven with an air
volume of up to approx. 260 l/min (e.g. tire inflator, blow-out
pistol and paint spray gun). Due to the limited air output it is
not possible to use the compressor to drive tools with very high
air consumption (for example orbital sanders, die grinders and
hammer screwdrivers).

The equipment is to be used only for its prescribed purpose.
Any other use is deemed to be a case of misuse. The user / op-
erator and not the manufacturer will be liable for any damage
or injuries of any kind caused as a result of this.

Please note that our equipment has not been designed for use
in commercial, trade or industrial applications. Our warranty
will be voided if the equipment is used in commercial, trade or
industrial businesses or for equivalent purposes.