PKSA 20-Li A1
■
14
│
GB
│
IE
│
NI
│
CY
♦
Always clean the area around the chain oil tank
cap before filling to prevent dirt getting into
the chain oil tank.
Use a dry, lint-free cloth to do this.
♦
Turn the chain oil tank cap anticlockwise
and remove it.
The chain oil tank cap is connected to the
chain oil tank with an loss-prevention device
and cannot fall onto the floor.
♦
Add the supplied organic chain oil to the
chain oil tank.
Do not spill any chain oil while filling the chain
oil tank and do not fill the tank to overflowing.
♦
Wipe up any spilt chain oil immediately.
♦
Turn the chain oil tank cap clockwise to
close it.
Tightening and checking the saw chain
WARNING!
►
Wear protective gloves! There is a risk of
injury from the sharp cutting teeth!
►
Check the chain tension before every use.
♦
Undo the fixing screw .
♦
Turn the chain tensioning ring in a clockwise
direction to increase the tension.
♦
The saw chain must lie against the underside
of the blade.
Check whether the saw chain (with the chain
brake off, pull the front hand guard to the rear)
can be drawn by hand over the guide rail
.
♦
Now tighten the fixing screw completely.
NOTE
►
A new saw chain stretches and must be
tightened more often.
Use
Before starting the tool, always check that:
■
The protective equipment and cutting equipment
is complete and in perfect working order.
■
All screw connections are firmly tightened.
■
All moving parts can move smoothly and freely.
Switching on and off
Switching on:
♦
Press the safety lock-out and keep it pressed
and then press the ON/OFF switch .
♦
After starting, the safety lock-out can be
released again.
Switching off:
♦
Release the ON/OFF switch .
Optimal working procedures
Get to know the chainsaw before you start to use it.
Checking and adjusting the chain
lubrication
ATTENTION!
►
Never work without chain lubrication!
If the saw chain runs dry, the cutting equip-
ment may become irreparably damaged in a
short time.
►
Always check the chain lubrication before
starting work.
NOTE
►
Use only saw chain oil, preferably biode-
gradable. Do not use waste oil, motor oil, etc.
►
While working, check whether the chain
lubrication is working correctly.
♦
With the chainsaw running, hold it over a sawn
off tree stump or a suitable ground sheet.
If the lubrication is adequate, a light film of oil
forms on the tree stump or the ground sheet
(see fold-out page, fig. D).
Summary of Contents for 327520
