Parkside 339390 1910, Operating And Safety Instructions Manual

7

GB

23  Replace table inserts when worn!
24  Avoid overheating of the saw teeth.
25  When sawing plastic, avoid melting of the plastic.

Use the appropriate saw blades for this purpose. Replace 
damaged or worn saw blades immediately.
When the saw blade overheats, stop the machine. Allow 
the saw blade to cool down before using the machine 
again.

Attention: Laser radiation
Do not stare into the beam
Class 2 laser

Protect yourself and you environment from acci-
dents using suitable precautionary measures!

• Do not look directly into the laser beam with unprotected 

eyes.

• Never look into the path of the beam.

• Never point the laser beam towards reflecting surfaces and 

persons or animals. Even a laser beam with a low output 
can cause damage to the eyes.

• Caution

 -

 methods other than those specified here can result 

in dangerous radiation exposure.

• Never open the laser module. Unexpected exposure to the 

beam can occur.

• The laser may not be replaced with a different type of laser.

• Repairs of the laser may only be carried out by the laser 

manufacturer or an authorised representative.

Residual risks
The machine has been built according to the state 
of the art and the recognised technical safety re-
quirements. However, individual residual risks can 
arise during operation.

• Health hazard due to electrical power, with the use of im-

proper electrical connection cables.

• Furthermore, despite all precautions having been met, some 

non-obvious residual risks may still remain.

• Residual risks can be minimised if the „safety instructions“ 

and the „Proper use“ are observed along with the whole of 
the operating instructions.

• Do not load the machine unnecessarily: excessive pressure 

when sawing will quickly damage the saw blade, which re-
sults in reduced output of the machine in the processing and 
in cut precision.

• When cutting plastic material, please always use clamps: 

the parts which should be cut must always be fixed between 
the clamps.

• Avoid accidental starting of the machine: the operating but-

ton may not be pressed when inserting the plug in an outlet.

• Use the tool that is recommended in this manual. In doing so, 

your machine provides optimal performance.

• Hands may never enter the processing zone when the ma-

chine is in operation.

• Release the handle button and switch off the machine prior 

to any operations.

Warning!

 This electric tool generates an electromagnetic field 

during operation. This field can impair active or passive medical 
implants under certain conditions. In order to prevent the risk of 
serious or deadly injuries, we recommend that persons with medi-
cal implants consult with their physician and the manufacturer of 
the medical implant prior to operating the electric tool.

7.  Technical data

AC motor.....................................................220 - 240 V~ 50Hz

Power S1* ..................................................................2000 Watt
Idle speed n

0 

1

st

 gear ........................................................................3200 min

-1

2

nd

 gear .......................................................................4500 min

-1

Carbide saw blade ...............................ø 255 x ø 30 x 2,2 mm
Number of teeth .......................................................................48
Maximum tooth width of saw blade .................................. 3 mm
Swivel range  .................................................. -45° / 0°/ +45°
Mitre cut ....................................................0° bis 45°  to the left
Saw width at 90° ................................................. 340 x 90 mm
Saw width at 45° ................................................. 240 x 90 mm
Saw width at 2 x 45° 
(double mitre cut) .................................................. 240 x 45 mm
Protection class .................................................................... II /   
Weight .......................................................................ca. 14,7 kg
Laser class ................................................................................... 2
Wavelength of laser ........................................................ 650 nm
Laser output .....................................................................< 1 mW

* S1 operating mode, continuous duty

The work piece must have a minimum height of 3 
mm and a minimum width of 10 mm. 
Make sure that the workpiece is always secured 
with the clamping device.

Noise

Total noise values determined in accordance with EN 62841.
Sound pressure level L

pA

 ............................................ 97,2 dB(A)

Uncertainty K

pA

 ......................................................................3 dB

Sound power level L

WA

 ............................................110,2 dB(A)

Uncertainty K

WA

 .....................................................................3 dB

Wear hearing protection.

The effects of noise can cause a loss of hearing

The above-mentioned noise emission values were measured in 
accordance with a standardised test procedure and can be 
used to compare one power tool with another.
The above-mentioned noise emission values can also be used 
for the preliminary assessment of exposure.

Warning:

• The noise emissions during the actual use of the power tool 

may differ from the above-mentioned values depending on 
the power tool being used, in particular on the type of work-
piece being processed.

• Try to keep emissions as low as possible. For example: Limit 

your working time. In this regard, all the operational cycle 
phases must be taken into consideration (such as the times 
when the tool is switched off or running idle).