GB
│
IE
│
NI
│
CY
│
7
■
PAAS 12 A2
Before use
Charging the battery pack
CAUTION!
►
Always unplug the appliance before you
remove the battery pack from or connect
the battery pack to the high-speed battery
charger .
NOTE
►
Never charge the battery pack if the ambient
temperature is below 10°C or above 40°C.
If a lithium-ion battery is to be stored for an
extended period, the charge level should be
checked regularly. The optimum charge level is
between 50% and 80%. The storage climate
should be cool and dry and the ambient tem-
perature should be between 0°C and 50°C.
♦
Connect the battery pack to the high-speed
battery charger .
♦
Insert the power plug into the socket. The
control LED
lights up red.
♦
The green control LED indicates that the
charging process is complete and the battery
pack is ready for use.
♦
Push the battery pack back into the appli-
ance.
♦
You should always switch the high-speed
charger
off for at least 15 minutes between
successive charging processes. Also disconnect
the power plug from the mains power socket.
Attaching/disconnecting the battery
pack to/from the appliance
Attaching the battery pack
♦
Click the battery pack into the handle .
Removing the battery pack
♦
Press the release buttons and remove the
battery pack .
Checking the battery charge level
♦
Press the safety lock-out and the ON/
OFF switch to check the charge level of the
battery. The status/remaining charge will be
shown on the battery charge level display
as follows:
RED/ORANGE/GREEN = maximum charge/
performance
RED/ORANGE = medium charge/performance
RED = low charge – charge the battery
Attaching/removing the grip bracket
NOTE
►
The grip bracket cannot be attached/
removed while the saw blade is attached.
Attaching the grip bracket (see fig. A–D)
♦
Press the release button .
♦
Push the grip bracket over the guides on the
base plate and onto the appliance.
♦
Lock the release button .
Removing the grip bracket
♦
Press the release and pull the grip
bracket
forwards out of the guides.
Fitting/changing the saw blade
Wear protective gloves when fitting/changing a
saw blade .
♦
Turn the quick-release chuck as far as it will
go in the direction of the arrow and hold it in
this position.
♦
Push the required saw blade into the quick-
release chuck as far as the stop.
CAUTION!
►
The teeth of the saw blade must point
downwards!
♦
Let go of the quick-release chuck ; it must
return to its initial position.
The saw blade is now locked.
Summary of Contents for 340502 1910
