PDSS 310 B5
■
12
│
GB
│
CY
■
Use only the genuine replacement parts
recommended by the manufacturer, otherwise
you could put users at risk . In doubt, contact the
Service Centre .
■
Clean the tool with a soft, dry cloth only .
■
Never use sharp or abrasive cleaning agents
under any circumstances .
Troubleshooting
Fault
Possible
cause
Remedy
Speed too
slow, air is
escaping from
the outlet .
Motor parts
jamming due
to dirt .
Check filter of
the pressure sup-
ply for contami-
nation, clean and
lubricate the de-
vice .
Pressure sup-
ply too low .
Check the pres-
sure supply filter
for contamina-
tion .
If necessary, re-
peat the steps
outlined above .
Tool will not
move; all com-
pressed air es-
caping through
the outlet .
Motor is
jammed due
to material
build-up .
Check filter of
the pressure sup-
ply for contami-
nation, clean and
lubricate the de-
vice .
Disposal
The packaging consists of environmen-
tally friendly material . It can be dis-
posed of in local recycling containers .
Do not dispose of the appliance in the normal
domestic waste!
Your local community or municipal authorities can
provide information on how to dispose of the worn-
out appliance .
Dispose of the packaging in an environ-
mentally friendly manner . Note
the labelling on the packaging and
separate the packaging material com-
ponents for disposal if necessary . The packaging
material is labelled with abbreviations (a) and
numbers (b) with the following meanings:
1–7: plastics, 20–22: paper and cardboard,
80–98: composites .
Your local community or municipal
authorities can provide information on
how to dispose of the worn-out product .
Dispose of lubricants and cleaning agents in an
environmentally friendly manner . Observe the
legal regulations .
■
Dispose of lubricant residues at a disposal
point . Do not allow lubricants to enter drains or
watercourses . Do not allow them to get into the
subsoil/soil . Make sure you use a suitable mat/
surface . Dispose of lubricants in accordance
with official regulations .
■
Dispose of contaminated maintenance material
and consumables at a collection point provided
for this purpose .
Summary of Contents for 373207 2104
