GB/IE/
CY
13
chuck (14).
7.7. Removing the additional scroll chuck
(Fig. 5)
Pull back and hold the locking sleeve (2) and
remove the scroll chuck.
7.8 Inserting the drill into the scroll chuck
(Figures 6-7)
Important!
Always pull the power plug before making
adjustments to the equipment.
Release the depth stop (13) as described in
7.2 and push it towards the drill handle. This
provides free access to the scroll chuck
(14).
Undo the scroll chuck (14) with the supplied
chuck key (15) by turning it anti-clockwise.
To ensure that it is perfectly positioned the
drill bit or tool should be inserted as far as
possible into the scroll chuck (14). After
inserting the drill bit or tool, tighten the scroll
chuck (14) by turning the chuck key (15)
clockwise until the drill bit or tool is secure.
Check that the drill bit is secure in the scroll
chuck (14).
Check at regular intervals that the drill bit or
tool is secure (pull the mains plug).
8. Starting up
Important!
To prevent all danger, the machine must
only be held using the two handles (3/6).
Otherwise there may be a risk of suffering an
electric shock if you drill into cables.
8.1 Status indicator (Fig. 1/Item 11)
The status indicator (11) lights up when the
power plug is connected.
8.2 ON/OFF switch (Fig. 9/Item 10)
First fit a suitable drill bit into the tool (see
7.3).
Connect the mains plug to a suitable
socket.
Position the drill in the position you wish to
drill.
To switch on:
Press the ON/OFF switch (10)
To switch off:
Release the ON/OFF switch (10)
Switching on continuous operation:
Secure the ON/OFF switch (10) with the
locking button (8).Important. It may only be
locked if the drill is set to rotate clockwise.
Switching off continuous operation:
Press the ON/OFF switch (10) briefly.
8.3 Adjusting the speed (Fig. 9/Item 10)
You can infinitely vary the speed whilst
using the tool.
Select the speed by applying a greater or
lesser pressure to the ON/OFF switch (10).
Select the correct speed: The most suitable
speed depends on the workpiece, the type
of use and the drill bit used.
Low pressure on the ON/OFF switch (10):
Lower speed
Greater pressure on the ON/OFF switch
(10): Higher speed
Tip:
Start drilling holes at low speed. Then
increase the speed in stages.
Benefits:
The drill bit is easier to control when
starting the hole and will not slide away.
You avoid drilling messy holes (for example
in tiles).
8.4 Preselecting the speed (Fig. 9/Item 9)
The speed setting ring (9) enables you to
define the maximum speed. The ON/OFF
switch (10) can only be pressed to the
defined maximum speed setting.
Set the speed using the setting ring (9) on
the ON/OFF switch (10).
Do not attempt to make this setting whilst
the drill is in use.
Anleitung_BMH_1100_4258398:_ 21.11.2008 7:40 Uhr Seite 13
Summary of Contents for BMH 1100
