8 GB/IE/CY
General safety advice
2. Electrical safety
To avoid danger to life from
electric shock:
a)
The mains plug on the device must
match the mains socket. The plug
must not be modified in any way.
Do not use an adapter plug with
devices fitted with a protective earth.
Unmodified plugs and matching sockets
reduce the risk of electric shock.
b)
Avoid touching earthed surfaces such
as pipes, radiators, ovens and refrig-
erators with any part of your body.
There is an increased risk of electric shock if
your body is earthed.
c)
Keep the device away from
rain or moisture.
Water entering
an electrical device increases the risk
of electric shock.
d)
Do not use the mains lead for
any purpose for which it was
not intended, e.g. to carry
the device, to hang up the device or
to pull the mains plug out of the mains
socket. Keep the lead away from
heat, oil, sharp edges or moving
parts of the device.
Damaged or tangled
mains leads increase the risk of electric shock.
e)
When working outdoors with an
electrical power tool always use ex-
tension cables that are also approved
for use outdoors.
The use of an extension
cable suitable for outdoor use reduces the risk
of electric shock.
f)
Use a residual current device (rCD) for
protection if operating the electrical
power tool in a moist environment is
unavoidable.
The use of an RCD reduces
the risk of electric shock.
3. Personal safety
a)
remain alert at all times, watch what
you are doing and always proceed
with caution. Do not use the device if
you are tired or under the influence
of drugs, alcohol or medication.
One
moment of carelessness when using the device
can lead to serious injury.
b)
Wear personal protective
equipment and always wear
safety glasses.
The wearing of
personal protective equipment such as dust
masks, non-slip safety shoes, safety helmets or
ear protectors, appropriate to the type of elec-
trical power tool used and work undertaken,
reduces the risk of injury.
c)
Avoid unintentional operation of the
device. Make sure that the switch is in
the “OFF” position before you insert
the mains plug into the mains socket.
Accidents can happen if you carry the device
with your finger on the switch or you have
already switched the device on before you
connect it to the mains.
d)
remove any setting tools or spanners
before you switch the device on.
A
tool or spanner left attached to a rotating part
of a device can lead to injury.
e)
Do not overestimate your own abili-
ties. Keep proper footing and balance
at all times.
By doing this you will be in a
better position to control the device, especially
in unforeseen circumstances.
f)
Wear suitable clothing.
Do not wear loose clothing or jewel-
lery. Keep your hair, clothing and
gloves clear of moving parts.
Loose
clothing, jewellery or long hair can become
trapped in moving parts.
4. Use and handling of the
electrical power tool
a)
Do not overload the device. Always
use an electrical power tool that is
intended for the task you are under-
taking.
By using the right electrical power
tool for the job you will work more safely and
achieve a better result.
Summary of Contents for KH 3114 PAINT SPRAY GUN
