10 GB/IE/CY
Q
Original ancillaries / and
accessories
J
Only use accessories and tools that are specified
in the operating instructions. The use of tools
and accessories other than those recommended
in the operating instructions could lead to an
increased risk of personal injury for you.
Q
Operation
Q
Operation
Take note of the mains voltage! The voltage must
agree with the information on the type plate of the
appliance (appliances that are designated as 230 V
can also be connected to 220 V).
Q
Switching On and Off
Switching on intermittent function:
j
Press the ON / OFF switch
1
.
Switching off intermittent function:
j
Release the ON / OFF switch
1
.
Switching on continuous operation :
j
Press the ON / OFF switch
1
, hold it pressed
and press the locking button
2
.
Switching off continuous operation:
j
Press the ON / OFF switch
1
then release it
again.
Q
Setting the oscillation speed
You can set the desired oscillation speed as
needed with the oscillation speed selector
10
.
The required oscillation speed depends on the
material being worked and can be determined
through practical tests.
Q
attaching a sanding pad
WarNING!
Before performing work on the
appliance, always disconnect the power.
Note:
Before attaching a new sanding pad
9
,
remove dust and dirt from the sanding plate
8
.
1. Open the two tensioning levers
7
by pushing
them up to clamp in a new sanding pad
9
or
when switching the sanding pads
9
for the
use with different material.
2. Slide the sanding pad
9
at one end under the
clamping bar
6
above the sanding plate
8
and clamp it tightly by pressing the tensioning
lever
7
back down.
3. Do the same at the other end. Make certain
that the sanding pad
9
rests firmly against the
sanding plate
8
. See also Fig. B and C.
4.
IMPOrTaNT!
To ensure that vacuuming of
dust through the sanding plate
8
is guaranteed,
the holes in the sanding pad
9
and the sand-
ing plate
8
must match up.
Various materials require different grit values. You
can read which grit value is best suited for which
work in our recommendations under “Tips and tricks”.
Q
Vacuuming dust
WarNING!
FIrE HazarD!
A risk of fire exists when working with
electrical appliances that have a dust
collection box
4
or can be attached to a vacuum
cleaner via an external suction adapter! Under
unfavourable conditions, such as flying sparks,
grinding of metal or metal remnants in wood, the
wood dust in the dust sack (or in the dust bag of
a vacuum cleaner) can ignite. This can happen
especially if the wood dust has paint particles on
it or is mixed with other chemical substances and
the sanded material is hot after extensive working.
You should therefore avoid overheating of products
being sanded as well as the appliance and always
empty the dust collection box
4
or the dust bag
of the vacuum cleaner before work pauses.
General safety advice / Operation
E-23503_XQ310_Content_LB3.indd 10
21.07.2008 16:26:29 Uhr
Summary of Contents for KH 3178 OSCILLATING SANDER
