24
GB
Recharging the battery
Allow a hot battery to cool before
charging.
Only charge the battery (8) when
the red LED on the charge status
indicator (7) is on.
1. Remove the battery (8) from the appli-
ance, as necessary (see „Removing/
inserting the battery“).
2. Insert the battery (8) in the charging
compartment of the battery charger (17).
3. Plug the battery charger (17) into a
mains outlet.
4. Once charging is complete, disconnect
the charger (17) from the mains supply.
5. Remove the battery (8) from the char-
ger (17).
Overview of the control display on
the charger (17):
Green LED lights up without battery
inserted:
Charger ready.
Green LED lights up:
Battery such alleged charged.
Red LED lights up:
Battery charging.
Red LED fl ashes:
Battery overheated
Red + green LEDs fl ash:
Defective battery
Inserting / removing the
device’s battery pack
Inserting the battery pack:
1. Move the rotation direction switch (11)
onto its middle setting (lock).
2. Slide the foot of the device onto the bat-
tery pack (8) until it clicks into place.
Removing the battery pack:
1. Push the release button (9) and pull the
battery pack (8) out towards the front
of the device.
Choice of gear
Slide the gear selector (4) to
1
or
2
,
corresponding to a low or high torque
selection.
1st gear ............................ 0-400 min
-1
2nd gear ......................... 0-1400 min
-1
A gear change may only be
performed in standstill mode!
Set the direction of
rotation
You can select the direction of rotation
with the direction switch (clockwise and
anticlockwise direction) and secure the
device against accidental start up.
The arrow on the direction switch indicates
the working direction.
1. Wait for the device to shut-down.
2. Push the direction switch (11) into the
desired position:
Clockwise direction:
To drill and screw in screws.
Press the
direction switch to the right with the
arrow pointing forwards
Counter-clockwise direction:
To unscrew screws.
Press the direction
switch to the left with the arrow poin-
ting backwards
3.
Switch lock:
Bring direction switch to
neutral position.
The direction changed may only be
performed in standstill mode.
Summary of Contents for PABS 20-Li E6
