Parkside PBLS 26 A1, Operating And Safety Instructions Manual

24

GB

-

Never start the device at the point where you have re-
filled fuel. 

-

Ensure that your clothing never comes into contact with 
fuel. Change your clothes immediately if they come into 
contact with fuel. 

-

After refuelling, ensure that the tank cover is closed cor-
rectly and securely again.

• Replace defective silencers.
• Always carry out a visual inspection before using of the de-

vice. Check in particular:

-

The throttle lever must move freely and should return to 
the neutral position independently and quickly. 

-

The on/off switch must be easy to operate.

-

All electrical cables such as spark plug cables and the 
spark plug connector must be in perfect condition to 
avoid sparks. The spark plug connector must be firmly 
seated on the spark plug. 

-

Keep the handle dry and free of oil and grease. Handles 
and guards must be undamaged. 

-

The fan must be undamaged. 

-

The collection bag must be undamaged. 

• Before starting work, always remove any objects lying on 

the ground that 

-

could be thrown when operating the device (when using 
as a blower)

-

could jam the vacuum tube (when using as a leaf vacuum)

-

could represent a hazard (stones, sticks, wire, bones, etc.)

C)  Operation

• Keep hands and feet away from the rotating parts.
• Do not run the combustion engine in closed rooms in which 

hazardous carbon dioxide can collect.

• Do not fit any devices or accessories to the device that are 

not provided by or approved by the manufacturer. 

• Keep work area clean and well lit. Cluttered or dark areas 

invite accidents.

• Do not use a tool that has a defective switch. Any tool that can-

not be switched on or off is dangerous and must be repaired.

• Never use the device:

-

Without having mounted all accessories intended for the 
respective use (when used as a leaf vacuum or blower)

-

Whilst other persons, in particular children or animals, 
are nearby.

-

In enclosed spaces, in an explosive environment, where 
flammable liquids, gases or dusts may be located.

• Therefore, always ensure that you have a safe and firm foot-

ing so that you can control the device and maintain your 
working posture even in the event of unexpected movements.

-

If possible, avoid working on wet or slippery ground. 
Avoid working on uneven or steep ground that does not 
guarantee the operator a safe working posture. 

-

Move slowly, do not run.  Pay attention to the ground 
conditions and any obstacles. 

• Make sure the device is fully assembled before starting it. 

-

Start the engine in an area at least 3 metres away from 
where you refuelled. 

-

Strangers should keep a safe distance of at least 15 me-
tres from the device because of flying parts.

-

Do not point the silencer and thus the exhaust gases at 
combustible materials. 

• Do not make any modifications to the engine.  

• Do not overload the device. Use the correct tool for your 

application. The correct tool will do the job better and safer 
at the rate for which it was designed.

• Make sure that the device does not come into contact with 

foreign bodies or with foreign bodies and dust that may be 
stirred up by the air.

• Never point the air stream at people or animals. 
• Never insert objects into the openings of the device and 

avoid sucking in large objects that could damage the fan.

• Keep your hands away from the intake grille and the air 

outlet during use and never block the fan. 

• Stop the engine:

-

When converting the device from a leaf vacuum to a 
leaf blower. 

-

When you are leaving the device unattended. 

-

Before refuelling

-

When you move to a different working area. 

• Stop the engine and disconnect the spark plug connector:

-

Before cleaning and maintenance work.

-

If a foreign body is sucked in. Check the device for dam-
age before operating it again.

-

If the device starts to produce unusual vibrations. 

-

When you are not using the device. 

• Do not leave the device on leaves, dry grass or other com-

bustible material when the engine is hot. Risk of fire!

• Do not work with the device in an explosive environment 

where flammable liquids, gases or dusts may be located. The 
device creates sparks which may ignite the dust or vapours.

• 

WARNING!

 Do not work near open windows. Watch out 

for children, pets and blow away foreign objects safely.

• Keep children, other people and pets away while using the 

tool. Distractions may cause you to lose control of the device.

• Do not overreach. Keep proper footing and balance at all 

times. This enables better control of the tool in unexpected 
situations.

• Stay alert, watch what you are doing and use common 

sense when operating the tool. Do not use a tool if you are 
tired or under the influence of drugs, alcohol or medication. 
A moment of carelessness when using the tool can result in 
serious injuries.

• Prevent unintentional starting. Carrying tools with your fin-

ger on the switch on invites accidents.

• Remove any adjusting tools or spanners before turning the 

tool on. A tool or spanner that is located in a rotating device 
part may result in injuries.

• It is recommended to operate the machine only at reason-

able times - not early in the morning or late at night when 
others may be disturbed. 

• Remove all foreign objects with a rake and brush before 

starting any blowing work.

• Where conditions are dusty, dampen the surface a little or 

use a sprinkler attachment.

• It is recommended to use the entire nozzle attachment so 

that the airflow can work close to the ground.

D)  Maintenance and storage

• Take care of tools.  Check for misalignment or binding of 

moving parts, breakage of parts and any other condition 
that may affect the tool’s operation. Have damaged parts 
repaired before using the device.  Many accidents are 
caused by poorly maintained tools.