GB/
MT
1. Introduction
Important.
When using the equipment, a few safety
precautions must be observed to avoid injuries
and damage. Please read the complete
operating instructions and safety information
with due care. Keep these operating
instructions in a safe place so that the
information is available at all times. If you give
the equipment to any other person, hand over
these operating instructions and the safety
information as well. We cannot accept any
liability for damage or accidents which arise due
to a failure to follow these instructions and the
safety information.
2. Safety information
CAUTION
Read all the safety regulations and
instructions.
Any errors made in following the
safety information and instructions set out
below may result in an electric shock, fire and/or
serious injury.
Keep all safety information and instructions
in a safe place for future use.
Protect yourself and your environment from
accidents by taking the appropriate
precautionary measures.
■
Do not use the chisel hammer for purposes
other than that for which it is designed.
■
Keep children away from air tools.
■
The equipment may only be operated by
persons who are rested and concentrated.
■
Connect the compressed air supply only
over a quick fastener coupling.
■
The working pressure must be set on the
pressure reducer.
■
Do not use oxygen or combustible gases as
power source. Danger of fire and explosion.
■
Do not exceed the maximum permissible
operating pressure.
■
Only operate the equipment with the
pressure required for the relevant operation.
This will help to prevent an unnecessarily
high noise level, increased wear and
resulting faults.
■
Wear the necessary protective clothing, in
particular impact-proof safety goggles, ear
muffs and safety gloves, when working with
the chisel hammer.
■
Do not use the equipment in idling mode in
order to prevent the chisel being catapulted
out uncontrolled.
■
Beware of fragments of the workpiece,
accessory parts or the plugged-in chisel
being catapulted away a high speed when
carrying out chiseling work.
■
Protect third parties from danger by
providing suitable protection of the
surrounding areas from parts which may be
catapulted away when working with the
chisel hammer or if the chisel should break.
■
Please note that there is a risk of the
workpiece being destroyed when chiseling.
■
Make sure that the workpiece is fixed
securely.
■
Use only a suitable tensioning spring (5)
(supplied). Replace the tensioning spring if it
is worn, broken or bent. This will help to
prevent injuries.
■
Sparks may be created when you work with
this equipment. It is important therefore that
you never work with this equipment near
combustible materials, liquids or gases.
■
Wear a helmet during overhead work.
■
Using this equipment can cause bruises,
grazes, cuts and burns. Wear gloves.
■
The user must be physically capable of
operating the equipment.
■
When using the equipment, be sure to adopt
a comfortable posture and change your
posture repeatedly in order to avoid physical
complaints.
■
Never touch the chisel during and after
working with the equipment. Fingers and
hands may be injured. The chisel can
become hot.
■
Use only original spare parts which have
been produced specifically for this
equipment.
■
When you release the quick-lock coupling,
hold the hose securely in your hand and
never use defective connections. This will
39
Anleitung_LB5_4139034:_ 13.04.2011 13:50 Uhr Seite 39
Summary of Contents for PDMH 4500 A1
Page 3: ...3 1 5 2 3 4 2 1 5 11 6 7 8 9 10 4 Anleitung_LB5_4139034 _ 13 04 2011 13 49 Uhr Seite 3...
Page 4: ...4 3 2 3 1 Anleitung_LB5_4139034 _ 13 04 2011 13 50 Uhr Seite 4...
Page 58: ...58 Anleitung_LB5_4139034 _ 13 04 2011 13 50 Uhr Seite 58...
Page 59: ...59 Anleitung_LB5_4139034 _ 13 04 2011 13 50 Uhr Seite 59...
