9
GB/CY
If using an extension lead, always use one that
is approved for outdoor use.
J
If a dangerous situation arises, pull the mains
plug immediately out of the mains socket.
J
Always work with the mains lead leading
away from the rear of the device.
J
DANGeR OF FIRe FROM FLy-
ING SPARKS!
Grinding metal
creates flying sparks. For this reason,
always make sure that nobody is placed in any
danger and that there are no inflammable ma-
terials near the working area.
WARNING!
NOxIOUS FUMeS!
Working
with harmful / noxious dusts represents a risk to
the health of the person operating the device
and to anyone near the work area.
J
Wear protective glasses, hearing
protection, dust protection mask and
protective gloves.
J
DANGeR OF BURNS!
The workpiece gets
hot during grinding. Never touch the part you
are grinding. Allow the workpiece to cool suffi-
ciently first. When grinding for longer periods,
stop grinding from time to time and allow the
workpiece to cool before continuing. Do not
operate the device for continuous periods ex-
ceeding 30 minutes.
J
The double grinding machine is intended for
dry grinding of the surfaces of metal objects.
The device may only be used for dry grinding.
J
Do not grind materials containing asbestos.
Asbestos is a known carcinogen.
J
Do not use damaged grinding wheels
4
.
J
Only use grinding wheels with details that cor-
respond with those given on the device rating
plate. The circumferential speed should be
equal to or greater than the value given on the
device rating plate.
J
Adjust the eye guard mounts
2
(spark deflectors)
and the eye guards
3
periodically so that wear
on the grinding wheels can be evened out.
Keep the gap as small as possible.
J
Avoid contact with the moving grinding wheel.
J
Never leave the device working unattended.
J
Never use the device for a purpose for which it
was not intended.
J
Before you insert the mains plug into the sock-
et, always check that the device is switched off.
J
Always switch the device on before bringing
the workpiece into contact with the grinding
wheel. After grinding, lift off the workpiece
before switching the device off.
J
Hold the workpiece firmly with both hands at
all times when working.
J
Always keep proper footing and balance.
J
After you have finished grinding metal, allow
the grinding wheel(s) to come to a standstill.
J
When taking a break from your work, before
carrying out any tasks on the device itself and
when you are not using the device, always pull
the mains plug out of the mains socket.
J
Handle the device carefully and treat it with re-
spect. Always keep the device clean, dry and
free of oil or grease.
J
Remain alert at all times! Always watch what
you are doing and proceed with caution. Do
not use the device if you cannot concentrate or
you are feeling unwell.
J
Store grinding wheels in such a way that they
are not subject to mechanical loads or damag-
ing environmental influences.
Q
Before use
Q
Assembly
j
Before using the device for the first time make
sure that you have fitted all its parts.
1) Attach the two eye guard mounts
2
to the in-
side of the wheel guard covers
7
, one each
on the left and right sides. Use the illustrated
fixings in the arrangement shown (see Figs. G, H).
2) Attach the eye guards
3
to the eye guard
mounts
2
, one each on the left and right
sides. Use the illustrated fixings in the arrange-
ment shown (see Figs. I, K).
Note:
The illustrations show the left side.
3) Attach the two workpiece / tool rests
5
to the
inside of the wheel guard covers
7
, one each
on the left and right sides. Use the illustrated
fixings in the arrangement shown (see Figs. L, M).
Note:
The illustrations show the left side.
j
Mount the double grinding machine on a firm,
level surface, if at all possible on a fixed sup-
port, e.g. working surface, workbench. Use the
General safety advice / Before use
Summary of Contents for PDOS 200 A1 - 3
