PDT 40 H6
■
8
│
GB
│
IE
Operation
♦
Load the magazine of the pneumatic nail
and staple gun as described in the section
“Filling the magazine”.
♦
Set the correct working pressure using the
pressure reducer (not supplied).
NOTE
■
Make sure that you do not exceed the maxi-
mum working pressure of 8 bar on the tool.
Excessive working pressure does not mean
increased output; it merely increases the
compressed air consumption and accelerates
tool wear.
♦
Switch on the compressor.
Run the compressor once until the maximum
tank pressure has been reached and then
switch off the tool.
♦
Place the tool on the workpiece and pull the
trigger .
NOTE
■
The pneumatic nail and staple gun
is equipped with a safety yoke .
The fastener material does not leave
the tool until the opening of the pneumatic
nail and staple gun is pressed against the
workpiece and the trigger is pressed.
■
Check whether the fastener is properly driven
in according to requirements.
–
If the fastener protrudes, increase the air
pressure in increments of 0.5 bar.
–
If the fastener is too deep, reduce the air
pressure in increments of 0.5 bar.
■
Alternatively, you can speed up the work by
holding the trigger .
♦
Place the pneumatic nail and staple gun onto
the workpiece.
♦
Press the tool onto the workpiece till the
opening is touching it. The fastener material
exits the tool.
♦
As long as you pull the trigger , a piece of
fastener material leaves the tool each time the
opening touches the workpiece.
■
Alternatively, you can keep the opening
of the tool permanently pressed onto the work-
piece.
♦
Each time you pull the trigger , a fastener
exits the tool.
NOTE
■
Fine adjustment is also possible with the
knurled screw .
♦
Turn the knurled screw down to sink the
fastener deeper into the workpiece.
♦
Turn the knurled screw up to sink the fastener
less deeply into the workpiece.
♦
Turn the exhaust cover to direct the escaping
air in the desired direction.
♦
Disconnect the tool from the compressor after
completing your work.
Removing jammed staples
If a staple/nail gets stuck in the magazine shaft,
immediately remove the compressed air supply
line.
♦
Open the magazine as described in the
section “Filling the magazine”.
♦
Open the face plate by pulling the face
plate quick-release lever in the direction of
the safety yoke .
♦
Remove the jammed fastener.
♦
Close the face plate by pulling the face
plate quick-release lever in the direction of
the exhaust cover .
♦
Close the magazine of the pneumatic nail
and staple gun as described in the section
“Filling the magazine”.
Summary of Contents for PDT 40 H6
