7
GB/IE/CY
Fixed mounting kit:
12
Mounting frame
13
Clamp plates 2 x
14
Screw clamps 2 x
15
Spacer plates 2 x
16
Screw
Q
Included items
Check that all the items and accessories
are present immediately after unpacking
the device:
1 Belt sander PEBS 900
1 Sanding belt
1 Dust collection box
1 Extraction adapter
(for external vacuum dust extraction)
1 Fixed mounting kit
1 Operating instructions
1 Booklet “Guarantee and service”
Q
Technical information
Belt sander:
Parkside PEBS 900
Nominal voltage:
230 V ~ 50 Hz
Nom. power input: 900 W
No-load belt speed: 180 - 340 m / min
No-load speed:
n
0
345 - 645 min
-1
Sanding belt
75 x 533 mm
Protection class:
II /
Noise and vibration data:
Values determined in accordance with EN 60745.
The sound pressure level (A-weighted) of the
device is typically 87 dB(A). Uncertainty K=3 dB.
The sound level while working can exceed
100 dB (A).
Wear ear protection!
Total vibration, EN 60745:
Vibration emission value a
h, D
= 2.828 m / s
2
Uncertainty K < 1.5 m / s
2
WarNING!
The vibration level given in these
instructions has been measured in accordance with
a standardised measurement procedure specified
in EN 60745 and can be used to compare devices.
Different uses of the device give rise to different vibra-
tion levels and in many cases they may exceed the
values given in these instructions. It is easy to underes-
timate the vibration load if the electrical power tool is
used regularly in particular circumstances.
Note:
If you wish to make an accurate assessment
of the vibration loads experienced during a particu-
lar period of working, you should also take into
account the intervening periods of time when the
device is switched off or is running but is not actual-
ly in use. This can result in a much lower vibration
load over the whole of the period of working.
The PEBS 900 belt sander has full-wave electronics
with additional control electronics, soft start with
inrush current limiting.
General safety advice for
electrical power tools
WarNING!
read all the safety advice
and instructions!
Failure to observe the safety advice and instructions
may result in electric shock, fire and / or serious injury.
KEEP ALL THE SAFETY ADVICE AND INSTRUCTIONS
IN A SAFE PLACE FOR FUTURE REFERENCE!
Introduction / General safety advice for electrical power tools
Summary of Contents for PEBS 900 SE
