7
GB/CY
Technical Data
Rated voltage:
230 V~ 50 Hz
Nominal power consumption: 200 W
Nominal stroke rate:
Level I: n
0
6500 min
-1
Level II: n
0
7500 min
-1
Level III: n
0
8500 min
-1
Stroke: ca.
2
mm
Protection class:
Noise and vibration data:
Measured values for noise are determined in accor-
dance with EN 60745. The A-weighted noise level
of the electrical power tool are typically:
Sound pressure level:
77.50 dB(A)
Sound power level:
88.50 dB(A)
Uncertainty K:
3 dB
Wear ear protection!
Evaluated acceleration, typical:
Hand / arm vibration a
h
= 2.066 m / s
2
Uncertainty K = 1.5 m / s
2
The vibration level given in these
instructions has been measured in accordance with
a standardised measurement procedure specified
in EN 60745 and can be used to compare devices.
Different uses of the device give rise to different vibra-
tion levels and in many cases they may exceed the
values given in these instructions. It is easy to underes-
timate the vibration load if the electrical power tool is
used regularly in particular circumstances.
Note:
If you wish to make an accurate assessment
of the vibration loads experienced during a particu-
lar period of working, you should also take into
account the intervening periods of time when the
device is switched off or is running but is not actually
in use. This can result in a much lower vibration
load over the whole of the period of working.
General safety advice for
electrical power tools
Read all the safety advice
and instructions!
Failure to observe the safety
advice and instructions may result in electric shock,
fire and / or serious injury.
Keep all the safety advice and instructions
in a safe place for future reference!
The term “electrical tool” used in the safety advice
refers to electrical tools powered by mains electrici-
ty (by means of a mains lead) and electrical tools
powered by rechargeable batteries (without a
mains lead).
1.
Workplace safety
a)
Keep your working area clean and
well lit.
Untidy or poorly lit working areas
can lead to accidents.
b)
Do not work with the device
in potentially explosive envi-
ronments in which there are
inflammable liquids, gases or dusts.
Electrical power tools create sparks, which can
ignite dusts or fumes.
c)
Keep children and other
people away while you are
operating the electrical tool.
Distractions can cause you to lose control of
the device.
2.
Electrical safety
a)
The mains plug on the device must match
the mains socket. The plug must not
be modified in any way. Do not use
an adapter plug with devices fitted
with a protective earth.
Unmodified
plugs and matching sockets reduce the risk of
electric shock.
b)
Avoid touching earthed surfaces such
as pipes, radiators, ovens and refrig-
erators with any part of your body.
Introduction / General safety advice for electrical power tools
Summary of Contents for PES 200 B1
