GB
28
2. Release the hexagon bolts (23) with
the open-end spanner (11).
3. Lower the planer blade guard (17)
and slide the blade holder (20) with
the planer blade (19) and clamping
plate (18) sideways out of the blade
shaft (21).
Use a small piece of wood to push it
out.
4. Disassemble the blade holder (20),
planer blade (19) and clamping plate
(18).
If the parts do not come apart by them-
selves, they may be covered in resin.
You can now rotate or replace the planer
blade.
Assembling the planer blade (fig.
A)
1. Clean the blade holder (20), planer
blade (19) and clamping plate (18) if
required.
2. Place the clamping plate (18) on a sur-
face with the lugs facing up.
3. Place the planer blade (19) onto the
clamping plate (18). The blade edge
should be on the top lugs. The groove
should be on the lower lugs.
4. Place the blade holder (20) onto the
planer blade (19) and clamping plate
(18). The hexagon bolts (23) should
point upwards. The holes fit over the
round lugs.
5. Turn the hexagon bolts (23) com-
pletely towards the blade holder (20)
and slide the blade holder along with
the planer blades (19) and clamping
plate (18) sideways into the blade
shaft (21).
The hexagon bolts should point for-
wards.
6. Tighten the hexagon bolts (23) by
hand.
7. Align the planer blade (19).
Aligning the planer blade (fig. A)
Goal: The planer blade must be at the
centre in the blade holder (20) and flush
with the planer sole (10).
1. Adjust the height of the planer blade
(19). Turn the grub screws (24) with
the hex key (12) (directions when look-
ing at the planer sole (10)).
⭯
:
⭣
⭮
:
⭡
To lift the planer blade, you may need
to loosen the hexagon screws (23)
slightly.
2. Check that the planer blade (19) is
flush with the planer sole by placing a
small piece of wood over both parts of
the planer sole. The planer blades must
touch the piece of wood evenly. Also
check in the transverse direction.
3. Clamp the blade holder (20) with
planer blades (19) and clamping plate
(18) centrally in the blade shaft (21)
firmly using the hexagon bolts (23).
4. After tightening the hexagon bolts
(23), check whether the planer blade
(19) is flush with the planer sole (10)!
If the planer blade is not flush with the
planer sole: Repeat the process.
Charging the battery
See also the charger instruction manual.
Notes
• If warm, allow the battery to cool be-
fore charging.
• Do not expose the battery to direct sun-
light for long periods and do not place
it on a radiator (max. 50°C).
Charging the battery
1. Connect the battery charger (14) to a
power outlet.
2. Push the battery (8) into the charging
slot of the battery charger (14).
Summary of Contents for PHA 12 B2
