7
GB/IE/CY
Introduction / General safety advice for electrical power tools
Technical information
Nom. power input:
160 W
Nominal voltage:
230 V ~ 50 Hz
Nominal speed:
n
0
13.000 min
-1
Nom. oscillation speed: n
0
26.000 min
-1
Backing plate:
360° rotatable
Protection class:
II /
Noise and vibration data:
Measured values for noise are determined in accord-
ance with EN 60745. The A-weighted noise level
of the electrical power tool are typically:
Sound pressure level:
76 dB(A)
Sound power level:
90 dB(A)
Uncertainty K:
3 dB
Wear ear protection!
Evaluated acceleration, typical:
Hand / arm vibration a
h
= 2,309 m / s
2
Uncertainty K = 1,5 m / s
2
WARNING!
The vibration level given in
these instructions has been measured in accordance
with a standardised measurement procedure specified
in EN 60745 and can be used to compare devices.
Different uses of the device give rise to different
vibration levels and in many cases they may exceed
the values given in these instructions. It is easy to
underestimate the vibration load if the electrical pow-
er tool is used regularly in particular circumstances.
Note:
If you wish to make an accurate assessment
of the vibration loads experienced during a particular
period of working, you should also take into account
the intervening periods of time when the device is
switched off or is running but is not actually in use.
This can result in a much lower vibration load over
the whole of the period of working.
General safety advice
for electrical power tools
WARNING!
Read all the safety advice
and instructions!
Failure to observe the safety
advice and instructions may result in electric shock,
fire and / or serious injury.
KEEP ALL THE SAFETY ADVICE AND INSTRUC-
TIONS IN A SAFE PLACE FOR FUTURE REFER-
ENCE!
THE TERM “ELECTRICAL TOOL” USED
IN THE SAFETY ADVICE REFERS TO ELECTRICAL
TOOLS POWERED BY MAINS ELECTRICITY (BY
MEANS OF A MAINS LEAD) AND ELECTRICAL
TOOLS POWERED BY RECHARGEABLE BATTER-
IES (WITHOUT A MAINS LEAD).
1.
Workplace safety
a)
Keep your working area clean and
well lit.
Untidy or poorly lit working areas
can lead to accidents.
b)
Do not work with the device
in potentially explosive envi-
ronments in which there are
inflammable liquids, gases or dusts.
Electrical power tools create sparks, which can
ignite dusts or fumes.
c)
Keep children and other peo-
ple away while you are op-
erating the electrical tool.
Distractions can cause you to lose control of
the device.
2.
Electrical safety
To avoid danger to
life from electric shock:
a)
The mains plug on the device must match
the mains socket. The plug must not
be modified in any way. Do not use
an adapter plug with devices fitted
with a protective earth.
Unmodified
plugs and matching sockets reduce the risk of
electric shock.
Summary of Contents for PHS 160
