PMBA 20-Li B2
■
8
│
GB
│
IE
Before use
Charging the battery pack (see fig. D)
CAUTION!
►
Always unplug the appliance before you
remove the battery pack from or connect
the battery pack to the charger.
NOTE
►
Never charge the battery pack at an ambient
temperature of below 10°C or above 40°C.
If a lithium-ion battery is to be stored for an
extended period, the charge level should be
checked regularly. The optimum charge level
is between 50% and 80%. The storage climate
should be cool and dry and the ambient
temperature should be between 0°C and
50°C.
♦
Connect the battery pack
w
to the high-speed
charger
i
(see fig. D).
♦
Plug the mains plug into the mains power socket.
The green charge control LED
p
lights up
briefly; then the red control LED
o
lights up.
♦
The green control LED
p
indicates that the
charging process is complete and the battery
pack
w
is ready for use.
ATTENTION!
♦
If the red control LED
o
flashes, this means
that the battery pack
w
has overheated and
cannot be charged.
♦
If the red and green control LEDs
o p
both
flash, this means that the battery pack
w
is
defective.
♦
Push the battery pack
w
back into the appli-
ance.
♦
Switch off the charger for at least 15 minutes
between successive charging sessions. Also
disconnect the power plug from the mains
power socket.
Inserting/removing the battery pack
Attaching the battery pack:
♦
Push the battery pack
w
into the handle until it
clicks into place.
Removing the battery pack:
♦
Press the release button
e
and remove the
battery pack
w
.
Checking the battery charge level
♦
Press the battery charge level button
0
to
check the status of the battery (see also main
diagram or fig. D).
The status/remaining charge will be shown
on the battery display LED
q
as follows:
♦
RED/ORANGE/GREEN = maximum charge
RED/ORANGE = medium charge
RED = low charge – charge the battery
Fitting the additional handle
♦
Screw the additional handle
9
onto the left or
right of the appliance depending on how you
work (see fig. A on the fold-out page).
Changing the saw blade
WARNING! RISK OF INJURY!
►
Wear protective gloves to avoid injury.
NOTE
►
You can order replacement saw blades via
our Service hotline.
♦
Release the saw blade clamping lever
8
by
turning it clockwise (see fig. B on the fold-out
page).
♦
Undo the two cylinder head screws
r
using the
hex key
z
(see fig. C on the fold-out page).
♦
Flip up the protective cap
t
.
♦
Carefully remove the saw blade
6
. Start at the
guide rollers
7
(see fig. C on the fold-out page).
♦
Remove any sawdust with a brush or
compressed air.
Summary of Contents for PMBA 20-Li B2
