PPHA 20-Li B2
■
94
│
DE
│
AT
│
CH
♦
Schieben Sie den Spanauswurf in das Gerät.
♦
Arretieren Sie den Spanauswurf durch
drehen in Position „LOCK“.
Fremdabsaugung
Bei Verwendung von z. B. Werkstattsaugern muss
ggf. der Adapter für externe Absaugung ver-
wendet werden. Der Werkstattsauger muss für den
zu bearbeitenden Werkstoff geeignet sein.
Anschließen
♦
Stecken Sie ggf. den Adapter für externe Ab-
saugung fest auf den Spanauswurf auf.
♦
Schieben Sie den Schlauch eines zulässigen
Werkstattsaugers auf den Spanauswurf ,
oder ggf. auf den Adapter für externe Absau-
gung .
Entnehmen
♦
Ziehen Sie den Schlauch des Werkstattsaugers
vom Spanauswurf oder vom Adapter.
♦
Ziehen Sie ggf. den Adapter für externe Ab-
saugung ab.
Parkschuh (siehe Abb. B)
Der Parkschuh ermöglicht das Abstellen des
Gerätes ohne die Gefahr einer Beschädigung des
Werkstücks. Beim Arbeitsvorgang wird der Park-
schuh hoch geschwenkt und der hintere Teil der
Hobelsohle freigegeben.
Hobelvorgang
VORSICHT! RÜCKSCHLAGGEFAHR!
►
Führen Sie das Gerät nur eingeschaltet ge-
gen das Werkstück.
♦
Stellen Sie die gewünschte Spantiefe ein.
♦
Schalten Sie das Gerät ein.
♦
Setzen Sie das Gerät mit dem vorderen Teil
der Hobelsohle an das Werkstück an.
♦
Führen Sie das Gerät mit gleichmäßigem
Vorschub über die zu bearbeitende Fläche.
♦
Arbeiten Sie nur mit geringem Vorschub und
üben Sie den Druck mittig auf die Hobelsohle
aus. Zu schneller Vorschub mindert die Ober-
flächengüte und kann zur Verstopfung des
Spanauswurfes führen.
Kanten anfasen
Die in der vorderen Hobelsohle vorhandenen
V-Nuten ermöglichen ein einfaches Anfasen von
Werkstückkanten.
♦
Verwenden Sie je nach gewünschter Fasen-
breite die entsprechende V-Nut.
♦
Setzen Sie dazu den Hobel mit der V-Nut
auf die Werkstückkante auf und führen Sie ihn
an dieser entlang.
Parallelanschlag montieren
(nicht im Lieferumfang, siehe Abb. G)
HINWEIS
►
Nicht aufgeführte Ersatzteile (wie z. B. Akku,
Parallelanschlag oder Falztiefenanschlag)
können Sie über unsere Service-Hotline be-
stellen.
♦
Lösen Sie die Befestigungsschraube am
Gerät.
♦
Montieren Sie den Parallelanschlag mit
der Befestigungsschraube am Gerät.
Summary of Contents for PPHA 20-Li B2
