GB
- 13 -
Warning!
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specifi ed value
in exceptional circumstances.
The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful effect.
Keep the noise emissions and vibrations
to a minimum.
•
Only use appliances which are in perfect
working order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appli-
ance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Residual risks
Even if you use this electric power tool
in accordance with instructions, certain
residual risks cannot be rules out. The fol-
lowing hazards may arise in connection
with the equipment’s construction and
layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
6. Before starting the
equipment
Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Always pull the power plug before ma-
king adjustments to the equipment.
•
The machine must be set up so that it stands
firmly, i.e. it must be securely screwed to a
work bench or similar.
•
All covers and safety devices have to be pro-
perly fitted before the equipment is switched
on.
•
It must be possible for the grinding wheel to
run freely.
6.1 Assembling the spark defl ector
(Fig. 1/3/4/5)
•
Slide the spark deflector (3) under the safety
hood (4). Screw the spark deflector (3) to the
safety hood (4) using the adjustment screw
(10).
•
Use the screw (10) with the spring washer
(a), the washer (b) and the nut (c) which are
fastened to the spark deflector (3). To secure
you will need a screwdriver and a matching
open-ended spanner for holding steady on
the other side (Fig. 3).
•
Adjust the spark deflector (3) using the adjus-
ting screw (10) so that the distance between
the dry grinding wheel (5) and the spark de-
flector (3) is as small as possible and certainly
does not exceed 2 mm.
•
Adjust the spark deflector (3) periodically to
compensate for wear on the wheel.
6.2 Fitting the workpiece supports
(Fig. 1/6/6a/Item 7)
•
Secure the workpiece supports (7) to the grin-
der/sander using the star screws (6).
•
Push the screw (a) through the recess where
you want to fasten the workpiece support (7).
First mount the workpiece support (7), then
the washer (b) and the toothed washer (c).
Finally mount the star screw (6) and tighten.
Anl_4466144.indb 13
Anl_4466144.indb 13
22.04.13 13:18
22.04.13 13:18
Summary of Contents for PSDS 240 A1
Page 82: ...82 Anl_4466144 indb 82 Anl_4466144 indb 82 22 04 13 13 19 22 04 13 13 19...
Page 83: ...83 Anl_4466144 indb 83 Anl_4466144 indb 83 22 04 13 13 19 22 04 13 13 19...
Page 84: ...84 Anl_4466144 indb 84 Anl_4466144 indb 84 22 04 13 13 19 22 04 13 13 19...
Page 85: ...85 Anl_4466144 indb 85 Anl_4466144 indb 85 22 04 13 13 19 22 04 13 13 19...
