3
PSTDA 18-Li A1
GB
CY
Noise and vibration data:
Noise measurement value determined in accord-
ance with EN ISO 4871 The A-rated noise level of
the power tool is typically as follows:
Sound pressure level: 80 dB(a)
Sound power level:
91 dB(a)
Uncertainty K:
3 dB
Wear ear protection!
Weighted acceleration, typically:
Hand/arm vibration a
h
= 9.2 m/s
2
Uncertainty K = 1.5 m/s
2
NOTE
►
The vibration level specifi ed in these instruc-
tions has been measured in accordance
with a standardised measuring procedure
specifi ed in EN 60745 and can be used to
make equipment comparisons. The specifi ed
vibration emission value can also be used to
make an initial exposure estimate.
WARNING!
►
The vibration level varies in accordance with
the use of the power tool and may be higher
than the value specifi ed in these instructions
in some cases. There is a risk of underestima-
tion of the vibration load if the power tool is
used regularly in this manner. Try to keep the
vibration loads as low as possible. Measures
to reduce the vibration load are, e.g. wearing
gloves and limiting the working time. Wherein
all states of operation must be included (e.g.
times when the power tool is switched off and
times where the power tool is switched on but
running without load).
General Power Tool
Safety Warnings
WARNING!
►
Read all safety warnings and all instructions.
Failure to follow the warnings and instruc-
tions may result in electric shock, fi re and/or
serious injury.
Save all warnings and instructions for future
reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-
operated (cordless) power tool.
1. Work area safety
a)
Keep work area clean and well lit.
Cluttered
or dark areas invite accidents.
b)
Do not operate power tools in explosive
atmospheres, such as in the presence of fl am-
mable liquids, gases or dust.
Power tools cre-
ate sparks which may ignite the dust or fumes.
c)
Keep children and bystanders away while
operating a power tool.
Distractions can cause
you to lose control.
2. Electrical safety
a)
Power tool plugs must match the outlet.
Never modify the plug in any way.
Do not use any adapter plugs with earthed
(grounded) power tools.
Unmodifi ed plugs
and matching outlets will reduce risk of electric
shock.
b)
Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators.
There is an increased risk of elec-
tric shock if your body is earthed or grounded.
c)
Do not expose power tools to rain or wet
conditions.
Water entering a power tool will
increase the risk of electric shock.
d)
Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the power
tool. Keep cord away from heat, oil, sharp
edges or moving parts.
Damaged or entan-
gled cords increase the risk of electric shock.
IB_102866_PSTDA18-LiA1_LB7.indb 3
22.10.14 14:59
Summary of Contents for PSTDA 18-Li A1
