06
- Contains flammable gas under pressure.
- Take care not to heat the
refillable gas tank. Do not expose gas soldering iron to temperatures exceeding
50°C / 120°F or to prolonged sunlight. Otherwise there is risk of disintegration
or explosion.
- Do not make any changes to the gas soldering iron! The soldering
iron may not be modified in any way. Factory settings may
not be altered. - Only replacement parts recommended by the
manufacturer may be used.
It can be dangerous to modify or adjust the gas
soldering iron, to remove factory fitted parts or to use replacement parts other
than those recommended by the manufacturer.
- Read the refilling instructions before you refill the soldering iron.
Refilling the soldering iron incorrectly can lead to serious accidents.
- ever pierce the gas tank or expose it to fire.
Otherwise there is risk of
disintegration or explosion.
- To avoid the risk of damage to the soldering iron protect the gas
soldering iron from impact and do not allow it to fall on to the floor
- never use a gas soldering iron which shows signs of damage.
- If gas escapes from the system (smell of gas), take the system
outdoors immediately to a well-ventilated location away from
sources of ignition where the leak can be safely detected and
repaired. Carry out the leak test in the open only. Do not try to
detect leaks using a flame, use a gas leak detector spray or soapy
water.
There is danger of fire or explosion in case of of a leak. - Contact the
manufacturer or retailer in case of a leak.
- Work in a fire resistant environment on in the open.
Otherwise there is
danger of fire, explosion or suffocation.
- The soldering iron may not be used in an environment where
flammable fumes, flammable liquids or explosive materials are
present.
Otherwise there is risk of disintegration or explosion.
- THE TORCH MUST NOT BE IGNITED NEAR THE FACE, HANDS,
CLOTHING OR INFLAMMABLE MATERIAL AND DO NOT DIRECT THE
FLAME TOWARDS PERSONS.
Otherwise there is danger of burning. Maintain
a safe distance of min. 0.5 m on the side from all objects, as well as a min.
distance of 1 m from objects over the device.
- THE AIR VENTS ON THE SOLDERING ATTACHMENT GIVE OFF HOT
AIR. ENSURE THAT THE TORCH IS PLACED ON THE INTEGRATED TOOL
HOLDER EVEN DURING SHORT WORK BREAKS, TO AVOID IGNITING
THE TABLE SURFACE OR OTHER OBJECTS. DO NOT DIRECT THE HOT
AIR FLOW TOWARDS YOUR EYES, FACE, BODY OR OTHER PERSONS.
Otherwise there is danger of burning.
Summary of Contents for PT360
