PWSA 20-Li A1
GB
│
CY
│
11
■
■
Always remove the battery during work
breaks, when adjusting the appliance and
when it is not in use.
The appliance must be
kept clean, dry and free of oil and grease at all
times.
■
Remain alert at all times! Always pay attention
to what you are doing and act with common
sense.
Do not use the appliance if you are dis-
tracted or feeling unwell.
WARNING!
Always wear safety goggles.
WARNING!
Always wear a dust mask!
Before use
Charging the battery pack (see fig. A)
CAUTION!
►
Always pull out the plug before you remove
the battery pack from or connect the
battery pack to the charger.
■
Never charge the battery pack when the
ambient temperature is below 10°C or above
40°C.
♦
Connect the battery pack to the high-speed
battery charger (see fig. A).
♦
Insert the power plug into the socket. The control
LED lights up red.
♦
The green LED indicates that the charging
process is complete and the battery pack is
ready.
CAUTION!
♦
If the red control LED flashes, this means
that the battery pack has overheated and
cannot be charged.
♦
If the red and green control LEDs both
flash, this means that the battery pack is
defective.
♦
Switch off the charger for at least 15 minutes
between successive charging sessions. Also
disconnect the power plug from the mains
power socket.
Attaching/disconnecting the battery
pack to/from the appliance
Inserting the battery pack:
♦
Allow the battery pack to click into the
handle.
Removing the battery pack:
♦
Press the release button and remove the
battery pack .
Checking the battery charge level
♦
Press the battery charge level button to
check the status of the battery (see also main
diagram).
The status/remaining charge will be shown on
the battery display LED as follows:
♦
RED/ORANGE/GREEN = maximum charge
RED/ORANGE = medium charge
RED = low charge – charge the battery
Fitting the blade guard with quick
release
WARNING! RISK OF INJURY
►
Always switch the appliance off and remove
the battery before carrying out any work on
the appliance.
RISK OF INJURY
►
Always use the angle grinder with the blade
guard . The blade guard should be fitted
securely. Set this so that the highest possible
degree of safety is achieved, i.e. the smallest
possible part of the grinding disc is open to
the operator. The blade guard is designed
to protect the operator from fragments and
accidental contact with the grinding tool.
Summary of Contents for PWSA 20-Li A1
