background image

EN

What this Warranty Covers

Horizon Hobby, Inc. (“Horizon”) warrants to the original purchaser that the 
product purchased (the “Product”) will be free from defects in materials and 
workmanship at the date of purchase. 

What is Not Covered

This warranty is not transferable and does not cover (i) cosmetic damage, (ii) 
damage due to acts of God, accident, misuse, abuse, negligence, commercial 
use, or due to improper use, installation, operation or maintenance, (iii) modi-
fication of or to any part of the Product, (iv) attempted service by anyone other 
than a Horizon Hobby authorized service center, (v) Product not purchased 
from an authorized Horizon dealer, or (vi) Product not compliant with appli-
cable technical regulations. 
OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER 
WARRANTY OR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL 
IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED 
WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS 
FOR A PARTICULAR PURPOSE. THE PURCHASER ACKNOWLEDGES THAT THEY 
ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE 
REQUIREMENTS OF THE PURCHASER’S INTENDED USE. 

Purchaser’s Remedy

Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall be 
that Horizon will, at its option, either (i) service, or (ii) replace, any Product 
determined by Horizon to be defective. Horizon reserves the right to inspect 
any and all Product(s) involved in a warranty claim. Service or replacement 
decisions are at the sole discretion of Horizon. Proof of purchase is required 
for all warranty claims.  SERVICE OR REPLACEMENT AS PROVIDED UNDER 
THIS WARRANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY. 

Limitation of Liability

HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL 
OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR 
COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH CLAIM IS 
BASED IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY OR 
ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS BEEN ADVISED OF 
THE POSSIBILITY OF SUCH DAMAGES. Further, in no event shall the liability of 
Horizon exceed the individual price of the Product on which liability is assert-
ed. As Horizon has no control over use, setup, final assembly, modification or 

misuse, no liability shall be assumed nor accepted for any resulting damage 
or injury. By the act of use, setup or assembly, the user accepts all resulting 
liability. If you as the purchaser or user are not prepared to accept the liability 
associated with the use of the Product, purchaser is advised to return the 
Product immediately in new and unused condition to the place of purchase.

Law

These terms are governed by Illinois law (without regard to conflict of law 
principals).  This warranty gives you specific legal rights, and you may also 
have other rights which vary from state to state.  Horizon reserves the right to 
change or modify this warranty at any time without notice.

WARRANTY SERVICES
Questions, Assistance, and Services

Your local hobby store and/or place of purchase cannot provide warranty sup-
port or service. Once assembly, setup or use of the Product has been started, 
you must contact your local distributor or Horizon directly. This will enable 
Horizon to better answer your questions and service you in the event that 
you may need any assistance. For questions or assistance, please visit our 
website at www.horizonhobby.com, submit a Product Support Inquiry, or call 
877.504.0233 toll free to speak to a Product Support representative. 

Inspection or Services

If this Product needs to be inspected or serviced and is compliant in the 
country you live and use the Product in, please use the Horizon Online Service 
Request submission process found on our website or call Horizon to obtain a 
Return Merchandise Authorization (RMA) number. Pack the Product securely 
using a shipping carton. Please note that original boxes may be included, 
but are not designed to withstand the rigors of shipping without additional 
protection. Ship via a carrier that provides tracking and insurance for lost or 
damaged parcels, as Horizon is not responsible for merchandise until it arrives 
and is accepted at our facility. An Online Service Request is available at http://
www.horizonhobby.com/content/_service-center_render-service-center. If you 
do not have internet access, please contact Horizon Product Support to obtain 
a RMA number along with instructions for submitting your product for service. 
When calling Horizon, you will be asked to provide your complete name, street 
address, email address and phone number where you can be reached during 
business hours. When sending product into Horizon, please include your RMA 
number, a list of the included items, and a brief summary of the problem.  A 

Problem

Possible Cause

Solution

Aircraft will not con-
nect (after binding) 
to transmitter

Transmitter too near aircraft during connecting pro-
cess

Move powered transmitter a few feet from aircraft, disconnect and reconnect 
fl ight battery to aircraft

Aircraft or transmitter is too close to large metal ob-
ject, wireless source or another transmitter

Move aircraft and transmitter to another location and attempt connecting again

Bind plug left installed in bind port

Rebind transmitter to the aircraft and remove the bind plug before cycling power

Aircraft bound to different model memory (Model-
Match

TM

 radios only)

Select correct model memory on transmitter

Flight battery/Transmitter battery charge is too low

Replace/recharge batteries

Transmitter may have been bound using different 
DSM protocol

Bind aircraft to transmitter

Control surface does 
not move

Control surface, control horn, linkage or 
servo damage

Replace or repair damaged parts and adjust controls

Wire damaged or connections loose

Do a check of wires and connections, connect or replace as needed

Transmitter is not bound correctly or the incorrect 
model was selected

Re-bind or select correct model in transmitter

Flight battery charge is low

Fully recharge fl ight battery

BEC (Battery Elimination Circuit) of the ESC 
is damaged

Replace ESC

Controls reversed

Transmitter settings are reversed

Perform the Control Direction Test and adjust the controls on transmitter ap-
propriately

Motor power pulses 
then motor loses 
power

ESC uses default soft Low Voltage Cutoff (LVC)

Recharge fl ight battery or replace battery that is no longer performing

Weather conditions might be too cold

Postpone flight until weather is warmer

Battery is old, worn out, or damaged

Replace battery

Battery C rating might be too small

Use recommended battery

Limited Warranty

16

Summary of Contents for VisionAire AS3X





















Reviews: