background image

 

 

Routine maintenance 

Have the condition and efficiency of the gas pipe as well as the pressure regulator (if installed) 
checked periodically. If anomalies are found, do not repair and have the faulty part replaced. 
 
To ensure good performance and safety, the gas regulator taps must be greased periodically. 
 

Periodic lubrication of the taps or malfunctions of the appliance must only be carried out by 
qualified personnel. 

 
 

Service and parts 

Before leaving the factory, this appliance was tested and adjusted by specialist skilled staff to give the 
best operating results. Any subsequent necessary repairs or adjustments must be carried out with 
the greatest care and attention. 
 
For this reason, we strongly advise you always to contact the Dealer who sold you the appliance or 
Parmco Service Department, specifying the nature of the problem, the model of the equipment 
(Mod.), the product number (Prod. No.), and the serial number (Ser. No.). These data are provided in 
the plate on the cover of this manual. Always request the use of original spare parts. 
 

Warranty conditions 

You new appliance is covered by a warranty. The warranty conditions are provided in full in the 
warranty page at the back of this manual. Keep the receipt or delivery note, both of which 
documents your purchase of the appliance and provides proof of date of purchase, in a safe place 
together with the manual.  
 
 

Summary of Contents for HO-1


















Reviews: