background image

 

8

minutes, then gently scrubbed to remove residues. Filters can be placed in the 
dishwasher when the detergent has a low caustic content. High caustic content 
dishwasher detergents may discolour the aluminium filters and result in 
premature failure of the aluminium mesh. 
 

Carbon Filters 

These filters contain activated carbon and cannot be cleaned. These filters should 
be replaced depending on how often the hood is used and what type of cooking 
is being undertaken. High odour and high oil content cooking will result in more 
frequent replacement of the carbon filters. 
 

Lamp Replacement 

 

To replace the halogen lamps first rotate the stainless steel lens cover (A)  
counter-clockwise 

 

Remove the stainless steel lens cover taking care not to drop the glass lens 
(B). 

 

Remove the bulb. 

 

Replace the halogen bulb with a new 12 Volt - 10 watt replacement. Take 
care not to touch the new halogen bulb directly with fingers as this can result 
in the bulb failing. 

  

 
  

 
 
 
 
 
 
 
 
 
 
 
 
 
 

Make sure that the supply voltage ratings are compatible with those stated on 
the appliance data label. 
 
This appliance comes fitted with a AS/NZS rated 3 pin plug and can be connected 
to a suitable socket that supply voltage ratings compatible with those stated on 
the appliance data label. 
 

Electrical Connection

Summary of Contents for Tilta T1-6-2












Reviews: