background image

 

INSTRUCTION REF: IN166 
ISSUE NO. 6 
DATE  - 21.03.16 
Page 11 of 24 

 

www.parry.co.uk 

FAULT FINDING 
 

FAULT 

POSSIBLE CAUSE 

REMEDY 

HOB 

 

 

Incorrect flame picture, 
flame lift or noisy burner 
 

Incorrect burner pressure, 
Blocked or partially blocked 
injector. 
Inadequate ventilation. 
Burner faulty/corroded/blocked 

Check/adjust burner pressure 
Check /clean injector, 
Check ventilation. 
Check / clean burner and 
replace as necessary. 

Burners will not stay 
alight 

Faulty connection at 
thermocouple-valve, incorrectly 
located 

Remake connection, 
reposition thermocouple 

Burner goes out when 
turned to “low” 
 

Blockage in tap 

Clean and re-grease 

Irregular flame 

Burner ring/cap not correctly 
located, or low pressure 

Relocate and check pressure 
at test point. 

OVEN 

 

 

Failure to ignite 
 

Dirt or grease broken or loose 
connection 
 

Clean reconnect / replace 
H.T.Lead 

 

Incorrect spark gap 

Set gap 3-4mm 

Burner fails on low rate 

Loose Thermocouple 
 

Replace 
 

 

Faulty Magnet in F.F.D. 

Replace thermostat 

Burner fails on low rate 

Thermocouple out of position. 

Reposition 

 

Summary of Contents for P4BO

























Reviews: