background image

 

INSTRUCTION REF: IN166 
ISSUE NO. 6 
DATE  - 21.03.16 
Page 14 of 24 

 

www.parry.co.uk 

Instruction Ref 

CONVIN35 

Issue No. 

Date updated 

07/09/2011 

        

LPG 

– Conversion Instructions

 

 

Product 

 
P4BO 

– Paragon 4 Burner Oven 

 

For use with models with the following serial numbers 
 

Model 

From 

To 

P4BO-4 

11011812 

 

 

These instructions can be used for converting from Natural Gas to LPG  
 

LPG units are designed and tested in accordance with all current regulations 
enforced to run on the following gases only 

 

Propane G31 @ 37mbar 14.8” W.G.

 

 

PLEASE NOTE 

This conversion must be carried out by a Gas Safe Registered Engineer.

 

This conversion kit includes 

 

Description 

Product Code 

Quantity 

Hob valve 
bypass screw 

LPG hob valve bypass 
screw stamped with 50 

COPBPS-50 

Hob burner 
injector 

LPG hob burner injector 
stamped with 0.92 

HOBINJECT105 

Oven valve 
bypass screw 

LPG oven valve bypass 
screw stamped with 40 

COPBPS-40 

Oven burner 
injector 

LPG oven burner injector 
stamped with 0.99 

INJECT099 

Labels 

 

G31 ONLY,  

Instructions 

 

CONVIN35-4 

Summary of Contents for P4BO

























Reviews: