background image

Bernese Mountain Dog 

 Page 16 of 20 

Installation Instructions 

 

 

Operational Setup 

Step 1: Open the fan and vent caps (Bernese Mountain Dog G & L only). 

A.

 

This step only applies to the Bernese Mountain Dog G and L. 

B.

 

Before turning the antenna ON, always open the fan and vent caps. The type of cap may vary. 

C.

 

Ensure that the antenna is away from any liquids when the caps are open. 

 

Figure 15: Open the fan and vent caps. (Bernese Mountain Dog G & L) 

Step 2: Power on the antenna. 

A.

 

For Bernese Mountain Dog A & L,

 connect a power cord to the AC outlet on the outside of the 

case. 

B.

 

For Bernese Mountain Dog G,

 follow steps 2C-2G below. 

C.

 

Turn the battery pack ON by pressing and holding the power button for 3 seconds. The display on 

the battery pack will indicate the battery pack’s current battery life (%)

Do not hold the button for 

longer than 3 seconds; this will cause the battery pack to enter programming mode. To exit 
programming mode, turn the battery pack OFF then ON again.

 

D.

 

Set the AC output switch on the battery pack to ON. The switch can be accessed through the slot 
in the cover plate. 

E.

 

Shortly after turning on the battery pack, the fan will start. 

F.

 

To charge the battery pack, connect the battery pack charger to the DC charging port on the 
outside of the case. 

G.

 

See Page 19 for Battery Operation and Safety Guidelines.

 

 

Summary of Contents for Bernese Mountain Dog A





















Reviews: