background image

Bernese Mountain Dog 

 Page 19 of 20 

Installation Instructions 

 

 

Battery Operation and Safety Guidelines 

A.

 

To manually power ON/OFF, press and hold the power button (located on the top of the unit) for 3 
seconds. All LED lights/display should turn ON/OFF. 

B.

 

Holding the power button for longer than 3 seconds will cause the battery pack to enter 
programming mode. To exit programming mode, turn the battery pack OFF and then ON again. 

C.

 

Recharging the battery pack can be done with the included 48W Charging Adapter or with a Type-
C PD Charger with at least 45W of power and up to 65W maximum. 

D.

 

To use the AC outlet, slide the AC power switch to the ON position and press the power button. The 
solid red LED light will come on, which indicates that the AC outlet is on. A device plugged into the 
AC outlet must be 15-85W for the AC outlet to work. Otherwise, the AC outlet will automatically 
shut off. 

E.

 

If no power draw is detected after 90 seconds, the battery pack with shut OFF to conserve energy. 
While the unit is OFF, press and hold the power button until the display begins flashing. This 
activates continuous mode, and the entire unit will stay ON until manually turned OFF. 

F.

 

While plugged in and charging, the battery pack will allow pass-through charging to continue 
powering any devices that are plugged in to the battery pack. To disable this function, press and 
hold the power button for 2 seconds while the battery pack is charging. Repeat to re-enable pass-
through charging for all ports. 

G.

 

Warning: if the battery pack exceeds a safe operating temperature due to insufficient ventilation 
or a high-temperature environment, the unit will automatically shut OFF. 

H.

 

Keep out of reach of children. 

I.

 

The product may become uncomfortable warm, reaching 140°F (60°C) under extended, high-
power usage. While using the product, make sure to keep it away from materials that may be 
affected by high temperatures. 

J.

 

Hold on carefully when inserting or removing a cable. Make sure not to force or bend cables 
when inserting them into the charging ports. 

K.

 

Avoid inserting any foreign objects into the ports. 

L.

 

Do not attempt to open, alter, or modify the unit. 

M.

 

Do not use in temperatures over 100°F (40°C). 

N.

 

Do not expose the product to wet conditions such as water, rain, or snow. 

O.

 

Failure to follow these safety guidelines may cause personal injury and/or property damage 
to the product. It may also void the product warranty. 

 

 

Summary of Contents for Bernese Mountain Dog A





















Reviews: