background image

16 

When  the  battery  is  connected  and  does  not  work  for  48  hours 
continuously,  the  battery  will  enter  sleep  mode  and  keep  low  power 
consumption. At this time, the LCD screen cannot be lit and the motor 
cannot run. To wake up the battery, unplug and replug the communication 
cable on the battery or connect the battery to the charger for charging. 

Note:

 15 seconds is required to wait before replugging the communication cable. 

5.3 Precautions 

 

Do not use damaged batteries. 

 

Do not knock or squeeze the battery. 

 

Do not use an unofficial charger to charge the battery. 

 

Do not keep the battery in wet or immersed environment for a long 

time. 

 

Do  not  disassemble  and  repair  the  battery  without  permission.  If 

necessary, contact the local dealer. 

 

Keep  the  conductor  away  from  the  battery  interface  to  avoid 

damaging the battery components. 

 

After  using  the  battery,  cover  the  battery  interface  with  the 

protection cover. 

 

Do not use the battery below 26V. 

 

Before long-term storage, charge the battery to 60% and keep the 
ambient temperature at 15

-25

 

For  long-term  storage,  fully  charge  and  fully  discharge the  battery 

every  3  months  to  keep  the  battery  active.  After  that,  keep  the 

battery power at about 60%. Note that this operation can effectively 

improve the battery life. 

 

After long-term storage, please charge the battery to 100% before 

using it. 

 

Do  not  leave  the  battery  in  a  high  temperature  or  high  pressure 

container, such as in an outdoor car exposed to the sun. 

 

Please dispose of the discarded batteries properly according to local 

laws and regulations. 

Summary of Contents for Joy1.2 BS



























Reviews: