background image

2

Regulatory Notices

WARNING

This is Class A Product. In domestic environment this product may cause radio interference in which 

case the user may be required to take adequate measures.

警告使用者

這是甲類的資訊產品,在居住的環境中使用時,可能會造成射頻干擾,在這種情況下,使用者會被要

求採取某些適當的對策。

FCC Statement

This device has been tested and found to comply with the limits for a Class A digital device, 

pursuant to part 15 of the FCC Rules, these limits are designed to provide reasonable protection 

against harmful interference when the device is operated in a commercial environment. This device 

generates, uses and can radiate frequency energy and, if not installed and used in accordance with 

this manual, may cause harmful interference to radio communications. Operation of this device in 

a residential area is likely to cause harmful interference in which case the user will be required to 

correct the interference at his/her own expense.

FCC WARNING

Changes or modifications not expressly approved by the party responsible for compliance could void 

the user’s authority to operate the device.

Best Management Practice (BMP) for Perchlorate Materials in California 

States

This device includes perchlorate in the lithium battery.
Perchlorate material-special handling may apply when handling this device.
For detail, refer to http://www.dtsc.ca.gov/hazardouswaste/perchlorate.

Vermont Mercury Management Rules

LCD display lamps contain mercury. Dispose of them properly.

CE Mark

This device complies with the requirements of the EEC directive 2004/108/EC with regard to 

“Electromagnetic compatibility” and 2006/95/EC with regard to “Low Voltage Directive”.

Summary of Contents for PAT-110

























Reviews: