background image

Shaking Tower Kit

 ME

-

7018

13

012

-

16515A

Technical Support

For assistance with any PASCO product, contact PASCO at:

Check the PASCO website for the latest version of the instruction manual.

www.pasco.com/manuals

Limited Warranty 

For a description of the product warranty, see the PASCO catalog. 

Copyright 

The PASCO scientific 

Instruction Manual

 is 

copyrighted with all rights reserved. Permission is granted to non-profit educational institutions for reproduction of any part of this manual, 
providing the reproductions are used only in their laboratories and classrooms, and are not sold for profit. Reproduction under any other 
circumstances, without the written consent of PASCO scientific, is prohibited. Rev: 07/19. 

Trademarks 

PASCO, and PASCO scientific are 

trademarks or registered trademarks of PASCO scientific, in the United States and/or in other countries. For more information visit 

www.pasco.com/legal. 

Replacement Parts

None of the equipment items in ME-7018 Shaking Tower Kit are available separately. However, the 

items are included in other PASCO products. Check the PASCO catalog or the web site at 

www.pasco.com to find out what is included in each of the PASCO products.

Address: PASCO scientific

10101 Foothills Blvd.
Roseville, CA 95747-7100

Web:

www.pasco.com

Phone: +1 916-462-8384 (worldwide)

877-373-0300 (U.S.)

Email

support@pasco.com

Item

 In Model # 

Description of Model Number

Truss Set Screws (80 pack)

ME-6994

Truss Set Screws (pack of 80)

Tire, Structure

ME-6998A

Axle Spares

Wheel, Structure

ME-6998A

Axle Spares

Medium Axle

ME-6988A

Axle Spares

Nylon Spacer

ME-6988A

Axle Spares

#4 I-Beams

ME-6993

Truss Set Members

#3 I-Beams

ME-6993

Truss Set Members

#2 I-Beams

ME-6993 

Truss Set Members

#1 I-Beams

ME-6993

Truss Set Members

Half Round Connector

ME-6993

Truss Set Members

Mass, 20 gram

ME-8983

20 g Replacement Mass Set (set pf 6)

Mass, 50 gram

ME-8984

50 g Replacement Mass Set (set of 6)

Flat (F4) Beams

ME-6987

Structures Flat Members

Flat Round Connector

ME-6997

Full Round (XYZ) Connector Spares

Full Round Connector

ME-6997

Full Round (XYZ) Connector Spares

Sliding Connector

ME-6999A

Angle Connectors Spares

Rubber Cord

ME-8986

Rubber Cord 30 m Spool

Summary of Contents for ME-7018














Reviews: