background image

user manual

CONDIZIONI DI GARANZIA 

1. Pasian garantisce all’acquirente per 24 mesi le parti strutturali in acciaio e quelle non soggette ad usura a con-

dizione che l’acquirente compili e conservi la fattura come prova di acquisto.

Tale garanzia è valida a patto che l’acquirente:

a) abbia installato l’apparecchio nel rispetto delle norme vigenti;

b) utilizzi in modo appropriato l’apparecchio;

c) notifichi tempestivamente eventuali difetti di fabbrica.

2. Sono esclusi dalla garanzia i pezzi soggetti ad usura, e cioè: VETRO CERAMICO, GUARNIZIONI, MANIGLIE,

POMELLI, RIVESTIMENTI IN MAIOLICA, VERNICE SILICONICA, FUSIBILI DI SICUREZZA, GUARNIZIONI E

PARTI INTERNE ALLA CAMERA DI COMBUSTIONE.

3. La garanzia non copre danni causati da:

a) un’errata installazione o un uso improprio della stufa e dei suoi componenti;

b) acqua o liquidi caduti o versti anche accidentalmente sui componenti elettrici o elettronici;

c) fulmini o sbalzi di corrente;

d) eccessivo surriscaldamento della stufa o utilizzo di combustibili non idonei;

e) deterioramento da agenti fisici o chimici;

f ) trasporto o manomissione da personale non autorizzato.

4. PASIAN non si assume alcuna responsabilità per guasti su parti elettriche causate da un errato collegamento

elettricoo per quelli in cui non è possibile accertatre il buon  funzionamento dell’impianto elettrico e la corretta

messa a terra al momento del guasto e per danni causati da montaggio di termostufe e collegamenti a canne fu-

marie non conformi a quanto indicato nel seguente libretto.

5. La garanzia consiste nella fornitura e sostituzione gratuita delle parti difettose o di quelle ritenute tali dal nostro

Ufficio Tecnico. Le parti sostituite rimarranno in garanzia per il periodo decorrente sempre dalla data di acquisto.

6. La sostituzione di componenti con altri non originali fa decadere la garanzia.

7. Non è previsto nessun indennizzo per il periodo di inefficienza della stufa o termostufa in attesa di riparazione.

8. La garanzia è personale e non è cedibile a terzi.

9. Se durante il periodo di garanzia vengono riscontrati difetti o rotture, l’acquirente deve rivolgersi al rivenditore

presso il quale ha effettuato l’acquisto, che provvederà a verificare l’eventuale difetto.

Se il difetto viene confermato dalla casa costruttrice, il ricambio verrà messo a disposizione del cliente gratuita-

mente. Per agevolare le operazioni di sostituzione vi preghiamo di fornire le segunti

informazioni al momento della richiesta di sostituzioe:

a) nome e indirizzo del rivenditore;

b) data di acquisto;

c) nome, indirizzo e recapito telefonico dell’acquirente;

d) nome, indirizzo e recapito telefoico dell’installatore;

e) data dell’installazione;

f) matricola e modello dell’apparecchio.

10. Tutte le spese di trasporto sono a carico del cliente acquirente, come il diritto di chiamata, i costi

della manodopera, le spese di trasferta ed il chilometraggio tra la sede e il domicilio del cliente.

11. PASIAN presta garanzia esclusivamente alle condizioni succitate ed in nessun caso risponde

dei danni diretti o indiretti causati dalle stufe (termostufe) a cose o a terzi.

12. La messa in funzione dell’apparechio può essere fatta dal Centro Tecnico Autorizzato o dal

rivenditore; la garanzia avrà validità a partire dalla data riportata sullo scontrino fiscale o fattura.

NON SONO CONSIDERATI INTERVENTI IN GARANZIA

: interventi per pulizia bracere, cassetto ceneri, 

stufe(termostufa); taratura (combustione, temperatura, orario accensione..) esclusa la prima accensione; interventi

di manutenzione ordinaria; interventi per mancanza e/o caricamento combustibile e adeguamento nuovi parametri

di combustione; interventi per difetti di funzionamento legati a mancanza di pulizia o errata manutenzione;interventi

per riparazione/sostituzione di componenti elettrici danneggiati da sovratensioni o da cariche elettriche.

45

Summary of Contents for Fortuna

















































Reviews: