background image

10

          WARNING

E X P L O S I O N / F I R E

HAZARD
Read  ALL  safety

instructions before using

or handling the fuel cell.

Failure  to  follow  ALL

instructions may result in

explosion or fire. This may

cause  serious  personal

injuries  or  property

damage.
Keep  the  fuel  cell  away

from  heat,  sparks  and

open flame. Do not smoke

when  handling  or

operating tool or fuel cell.

Exposure to temperatures

above 120

°

F (49

°

C) may

cause the fuel cell to burst,

releasing flammable gas.

          WARNING

Sunlight  can  raise  the  inside  temperature  of  an

unventilated  motor vehicle or staorage container to

above 140

°

F (60

°

C).

Never puncture or attempt to open the fuel cell; it is

non-refillable.
Never incinerate, reclaim or recycle the fuel cell.
Never  smoke while installing or operating the metering

valve or tool.
Never inhale the spray.
Keep out of the reach of children.
Store fuel cell(s) in well-ventilated areas only.

NOTE

1. Never  attempt to reuse the metering  valve!

Replace with fresh fuel cell/valve, and dispose

of spent cell/valve properly.

2. When replacing fuel cell also clean or replace air

filter for optimum tool operation.

Fuel Cell

There is a second container inside the fuel cell. The inner

container  holds  the  fuel.  The  space  between  the  inner

container and the outer cylinder is filled with a gas, called the

propellant, which is under pressure.
To eject the fuel, propellant pressure squeezes the inner

fuel container, much as you squeeze a tube of toothpaste.

This squeezing action ensures that all the fuel is used, and

that  the  Cordless 

 

Framing  Nailer    can  operate  in  any

position.
Because of this container-within-a-container design, you

might hear the sound of fluid when shaking the fuel cell after

all the fuel has been used. This is the propellant, which

remains between the containers even after all the fuel has

been expelled.
If you expose the empty fuel cell to extreme temperatures,

the propellant gas will expand and could cause the container

to burst, releasing flammable gases.

Metering Valve

The metering valve contains a fuel metering system to inject

the correct amount of fuel into the combustion chamber.
The 

red 

metering valve is the only valve that will operate

properly with the Paslode Cordless framer.

Fuel Cell and Metering Valve

red

NOTE: Altitude Restriction

Paslode  Cordless  tools  are  powered  by  an  internal

combustion engine and are effected by altitude.  The

tool  may  lose  power  or  not  cycle  consistantly  at

elevations of 4000 feet or greater. 

 

Summary of Contents for 900420





















Reviews: